ECS-T1AY225R Datasheet, PDF (1/4 Pages) Panasonic Semiconductor – Tantalum Solid Electrolytic Capacitors/TE

Tantalum Solid Electrolytic Capacitors/TE
Surface Mount Type
Series: TE Type : T
s Features Standard
Japan
China
s Specifications
Category temp. range
-55 to 125°C
Rated W.V. Range
4 to 35 V .DC
Nominal Cap. Range
0.15 to 330 µ F
Capacitance Tolerance
DC Leakage Current
±20 % (120Hz/20°C)
I < 0.01 CV or 0.5(µA) after 2 minutes application of rated working voltage at 20°C (whichever is greater)
tanδ
Please see the attached standard products list
Resistance to Soldering Heat The capacitor shall withstand dipping into solder for 5±1 seconds at 260 ±5°C
Ta
After 500 hours exposure at 40 °C and 90 to 95 % R.H. without load, the capacitor shall meet
.
the following limits.
Moisture Resistance
Capacitance change ±10% of initial measured value
TE
tanδ
< initial specified value, miniatured size: < 150% of initial specified value.
DC leakage current < initial specified value
Endurance
After 2000 hours application of rated DC working voltage at 85°C or derated voltage at
125°C, the capacitor shall meet the following limits.
Capacitance change ±10% of initial measured value
tanδ
< initial specified value
DC leakage current < 125 % of initial specified value
s Marking
s Dimensions in mm (not to scale)
q Size Y
Polarity bar (+ side)
W.V.code
Cap. code
q Size X,C,V,D _Cap.(µF)
W.V. code
W.V. (V) 4 6.3 10 16 20 25 35
code G J A C D E V
Capacitance code
Capacitance(µF) 1 1.5 2.2 3.3 4.7 6.8
1st code
AE J NSW
Multiplier
10⁵ 10⁶ 10⁷
2nd code
5
6
7
(Ex.) A6: 1.0 x 10⁶ pF(1.0µF)
J5: 2.2 x 10 ⁵ pF(0.22µF)
h (for 6.3W.V. abbreviated to 6 V)
Polarity Bar(+side) W.V.(V)
(+)
P
(-)
L
P
w1
EIA code Size code L±0.2 W1±0.2 W2±0.1 H±0.2 P±0.3
3216
Y
3.2 1.6 1.2 1.6 0.8
3528
X
3.5 2.8 2.2 1.9 0.8
6032
C
6.0 3.2 2.2 2.5 1.3
5846
V
5.8 4.6 2.4 3.2 1.3
7343
D
7.3 4.3 2.4 2.8 1.3
h Each case side has different tereminal configuration
s Case size
W.V.(V.DC)
4(0G)
6.3(0J)
10(1A)
16(1C)
20(1D)
25(1E)
Cap.(µF)
Standard Miniature Standard Miniature Standard Miniature Standard Miniature Standard Miniature Standard Miniature
0.15 to 0.33
0.47 (474)
0.68 (684)
Y
Y
1.0 (105)
1.5 (155)
2.2 (225)
3.3 (335)
Y
4.7 (475) Y
Y
6.8 (685) Y
Y
10 (106) Y
Y
Y
Y
Y
Y
X
Y
Y
Y
Y
Y
Y
X
Y
X
Y
Y
X
Y
X
Y
X
C
X
Y
Y
X
Y
X
X
C
C
15 (156) Y
X
Y
22 (226)
X
Y
X
Y
33 (336)
X
C
X
47 (476)
C
X
C
X
68 (686)
C
D,V
C
100 (107) D,V
C
D,V
C
150 (157) D,V
D
220 (227)
D
D
X
C
X
C
X
C
C
X
D,V C
D,V C D,V
D,V
D
D
D
C
D,V
D,V C
D
D,V
330 (337)
D
35(1H)
Standard
Y
Y
Y
Y
X
X
X
C
C
D,V
D
Note : 1. ( )indicates the W.V. and capacitance code.
2. When selecting W.V. refer to page 20.
3. We recommend current sizes shown in the above table for new design, but conventional case size is available on request.
4. Other rating upon request (voltage, capacitance, tolerance, size)
Rev.02/04
Design, Specifications are subject to change without notice. Ask factory for technical specifications before purchase and/or use.
Whenever a doubt about safety arises from this product, please inform us immediately for technical consulation without fail.
 EE27 