QEB100-24S3P3 Datasheet, PDF (2/4 Pages) Power Mate Technology Co., LTD – 100 WATTS MAXIMUM OUTPUT POWER

Model
Number
Input
Range
QEB100-24S3P3
QEB100-24S05
QEB100-24S12
QEB100-24S15
QEB100-48S1P8
QEB100-48S2P5
QEB100-48S3P3
QEB100-48S05
QEB100-48S12
QEB100-48S15
18 – 36 VDC
18 – 36 VDC
18 – 36 VDC
18 – 36 VDC
36 – 75 VDC
36 – 75 VDC
36 – 75 VDC
36 – 75 VDC
36 – 75 VDC
36 – 75 VDC
Output ^{Output Current}
Output ⁽⁴⁾
Input Current _Eff ⁽⁴⁾ _Load
Voltage _{Min. load Full load} Ripple & Noise _{No load}⁽³⁾ _{Full load}⁽²⁾ (%) regulation
3.3 VDC
5 VDC
12 VDC
15 VDC
1.8 VDC
2.5 VDC
3.3 VDC
5 VDC
12 VDC
15 VDC
0mA
0mA
0mA
0mA
0mA
0mA
0mA
0mA
0mA
0mA
25A
20A
8.33A
6.67A
30A
30A
25A
20A
8.33A
6.67A
100mVp-p
100mVp-p
100mVp-p
100mVp-p
100mVp-p
100mVp-p
100mVp-p
100mVp-p
100mVp-p
100mVp-p
80mA
120mA
130mA
190mA
70mA
70mA
75mA
80mA
130mA
130mA
3997mA
89
4845mA
90
4843mA
90
4847mA
90
1389mA
85
1883mA
87
2022mA
89
2422mA
90
2422mA
90
2424mA
90
10mV
15mV
36mV
45mV
5.4mV
7.5mV
10mV
15mV
36mV
45mV
Note :
1.BELLCORE TR-NWT-000332. Case 1: 80% Stress, Temperature at 40ºC.
MIL-HDBK-217F Notice2 @Ta=25 ºC, Full load(Ground, Benign, controlled environment)
2.Maximum value at nominal input voltage and full load of standard type.
3.Typical value at nominal input voltage and no load.
4.Typical value at nominal input voltage and full load.
5.Maximum output deviation is 10% inclusive of trim. If remote sense is not being used, the + sense should be connected to its corresponding
+OUTPUT and likewise the –sense should be connected to its corresponding –OUTPUT.
6.The positive logic and pin length are optional ( see table ). The pin voltage is referenced to –Vin.
7.Heat sink is optional and P/N：7G-0029A-F, 7G-0030A-F, 7G-0031A-F, 7G-0032A-F.
8.The QEB100 meets EN55022 class A and class B only with external components connected before the input pin to the converter.
9.An external input filter capacitor is required if the module has to meet EN61000-4-4, EN61000-4-5.
The filter capacitor Power Mate suggest: Nippon chemi-con KY series, 220μF/100V, ESR 48mΩ.
10.BASEPLATE GROUNDING：Base-plate should be grounded at one of the four screw bolts prior to operation.
11.The converter is provided by basic insulation.
Page 2 of 4 Issued Date：2008/05/21