SSR01_14 Datasheet, PDF (1/3 Pages) Power Mate Technology Co., LTD – NON- ISOLATION DC-DC CONVERTER

SSR01 SERIES
NON- ISOLATION DC-DC CONVERTER
FEATURES
• SMALL SIZE AND LOW PROFILE :
L X W X H = 0.60” X 0.37” X 0.29”
• HIGH EFFICIENCY UP TO 95.5%
• LOW QUIESCENT CURRENT
• WIDE INPUT RANGE: 4.6 ~ 36VDC AND 3 ~ 5.5VDC
• ADJUSTABLE OUTPUT VLOTAGE
• OVER-CURRENT PROTECTION
• OUTPUT SHORT CIRCUIT PROTECTION
• OVER-TEMPERATURE PROTECTION
• LOW OUTPUT RIPPLE AND NOISE
APPLICATIONS
Wireless Network
Telecom/Datacom
• FIXED SWITCHING FREQUENCY
• NEGATIVE OUTPUT APPLICATION
• SAFETY MEETS UL60950-1, EN60950-1, & IEC60950-1
• CE MARKED
Industry Control System
• COMPLIANT TO RoHS II & REACH
Distributed Power Architectures
Semiconductor Equipment
Microprocessor Power Applications
DESCRIPTION
The SSR01-SERIES high performance switching regulators are suited to pick and place
mass production. It provides 1A output current and high efficiency up to 95.5%. The
SSR01 series feature output short circuit protection, over-current protection, and
T E C H N I C A L S P E C I F I C A T I O N A^oll^vs^ep^r-e^tec^mifi^pca^erti^ao^tn^urs^ea^pr^re^ott^ey^cp^tiⁱc^oaⁿl^. a^Tt^hn^eo^Sm^Si^Rna⁰l¹in^sp^eu^rit^e,^sfu^cl^al ⁿlo^aa^ld^soa^bn^ed ^u2^s5^eº^dC^toot^ch^oeⁿr^vw^ei^rs^te^ern^ao^pte^od^sitive
voltage into a negative voltage.
OUTPUT SPECIFICATIONS
INPUT SPECIFICATIONS
Output current
Voltage accuracy
Minimum load
Line regulation
Load regulation
Ripple and noise
(20MHz bandwidth)
See table
0% to 100% of Full load
10% to 90% of Full load
Vout = 1.2V to 8V
Vout = 8.1 to 15.5V
1000mA, max.
±2%Vout, max.
0%
± 0.2% Vout
± 0.6% Vout
± 0.3% Vout
50mVp-p
75mVp-p
Input voltage range for positive output
Vin>Vout(set)+0.5V
Vin>Vout(set)+1.5V
3.0 ~ 5.5VDC
4.6 ~ 36VDC
Input voltage range for negative output
(Note 6)
See table
Vin+|Vout|≦36V
4.6 ~ 32VDC
Maximum input current
Vin(min), Full load
1A
Input filter
C filter
Input reflected ripple current
100mA
ENVIRONMENTAL SPECIFICATIONS
Temperature coefficient
±0.015%/℃, max.
Load change step Peak deviation
Dynamic load response
50% 100% of F.L. Recovery time
150mV
250µs
SSR01-05S2P5
Output current limit for Positive output
others
400%
200%
Output short-circuit
Capacitor Load (Note 4)
Continuous, automatics recovery
470uF, max.
Output voltage overshoot-startup
1% Vout, max.
GENERAL SPECIFICATIONS
Efficiency (Note 3)
Isolation voltage
See table
None
Operating temperature range
Maximum case temperature
–40ºC ~ +105ºC(with derating)
105ºC
Storage temperature range
Lead-free reflow solder process
Moisture sensitivity level(MSL)
Thermal shock
Vibration
Relative humidity (non-condensing)
–55ºC ~ +125ºC
IPC J-STD-020D
IPC J-STD-033B
Level 1
MIL-STD-810F
MIL-STD-810F
0% to 90% RH
Over temperature protection
Internal IC junction
170 ºC
Switching frequency
See table FEATURE SPECIFICATIONS
Safety meets
Case material
Base material
Potting Material
Weight
MTBF (Note 1)
IEC60950-1, UL60950-1, & EN60950-1
Non-conductive black plastic
Non-conductive black plastic
Epoxy(UL94 V-0)
MIL-HDBK-217F
1.7g(0.067oz)
1.457 x 10⁷ hrs
Start up time
Nominal Vin and
constant resistive load
Power up
Remote ON/OFF
5ms
5ms
Remote ON/OFF (Note 5)
(Positive logic)
DC-DC ON
DC-DC OFF
Open or 2V < Vr < 5V
Short or 0V < Vr < 0.8V
Input current of Remote control pin Nominal Input -0.1mA ~ 0.1mA
Remote off state input current
Nominal Input
1.2mA
Note
1. MIL-HDBK-217F @Tc=70ºC, Full load.
2. Typical value at nominal input voltage and no load.
3. Typical value at min. or max. input voltage and full load.
4. Tested with min. input voltage and constant resistive load.
5. Positive output : The ON/OFF control PIN voltage is referenced to GND.
Negative output : The ON/OFF control PIN voltage is referenced to –Vout.
CAUTION: This power module is not internally fused. An input line fuse must always be used.
Page 1 of 3
www.pduke.com
2014/4/30