SPS-93100MW-CXX0G_15 Datasheet, PDF (2/5 Pages) Optoway Technology Inc – Multirate Digital Diagnostic SFP LC SINGLE-MODE TRANSCEIVER

Optoway
2
SPS-93100MW-CXX0
***********************************************************************************************************************************************************************
Absolute Maximum Ratings
Parameter
Symbol
Min
Max
Units
Notes
Storage Temperature
Tstg
-40
85
o_C
Operating Case Temperature
Topr
0
70
o_C
Air flow 1m/sec
Power Supply Voltage
Vcc
-0.5
3.6
V
Recommended Operating Conditions
Parameter
Symbol
Min
Power Supply Voltage
Vcc
3.1
Operating Case Temperature
Topr
0
Power Supply Current
Data Rate
I_{CC (TX+RX)}
125
Typ
3.3
230
2488
Max
3.5
70
300
2670
Units / Notes
V
o_{C / Air flow 1m/sec}
mA
Mb/s
Transmitter Specifications (0^oC < Topr < 70^oC, 3.1V < Vcc < 3.5V)
Parameter
Symbol
Min
Typ
Max
Units
Notes
Optical
Optical Transmit Power
Output Center Wavelength
Output Spectrum Width
Po
1
---
5
dBm
1
λ
λc –5.5
λc
λc +7.5
nm
2
∆λ
---
---
1
nm -20 dB Width
Side Mode Suppression Ratio
SMSR
30
dB
Extinction Ratio
Output Eye
E_R
8.2
---
---
dB
Compliant with Telecordia GR-253-GORE and ITU-T Recommendation G.957
Optical Rise Time
t_r
Optical Fall Time
t_f
Relative Intensity Noise
RIN
150
ps
20 % to 80% Values
150
ps
20 % to 80% Values
-120
dB/Hz
Dispersion Penalty
2.5
dB
3
Electrical
Data Input Current – Low
Data Input Current – High
I_IL
-350
I_IH
µA
350
µA
Differential Input Voltage
V_IH - V_IL
0.5
TX Disable Input Voltage – Low
T_{DIS, L}
0
TX Disable Input Voltage – High
T_{DIS, H}
2.0
TX Disable Assert Time
T_ASSERT
TX Disable Deassert Time
T_DEASSERT
2.4
V
Peak-to-Peak
0.5
V
4
Vcc
V
4
10
µs
1
ms
TX Fault Output Voltage -- Low
T_FaultL
0
0.5
V
5
TX Fault Output Voltage -- High
T_FaultH
2.0
Vcc+0.3
V
5
1. Output power is power coupled into a 9/125 µm single mode fiber.
2. ITU-T G.694.2 CWDM wavelength from 1270 nm to 1610 nm, each step 20 nm.
3. Specified at 2000 ps/nm dispersion over G.652/G.654 fiber with center wavelength range of 1464.5 to 1617.5 nm.
4. There is an internal 4.7K to 10K ohm pull-up resistor to VccTX.
5. Open collector compatible, 4.7K to 10K ohm pull-up to Vcc (Host Supply Voltage).
Receiver Specifications (0^oC < Topr < 70^oC, 3.1V < Vcc < 3.5V)
Parameter
Symbol
Min
Typ
Optical
Sensitivity @ OC-48
Sens1
-9
Sensitivity @2X Fibre Channal
Sensitivity @Gigabit Ethernet
Sensitivity @OC-12
Sensitivity @OC-3
Sens2
-9
Sens3
-9
Sens4
-9
Sens5
-18
Signal Detect -- Asserted
Pa
---
Signal Detect -- Deasserted
Signal detect – Hysteresis
Pd
-40
---
3
Max
-30
-30
-30
-30
-30
-30
---
Units
Notes
dBm
6
dBm
7
dBm
7
dBm
6
dBm
6
dBm Transition: low to high
dBm Transition: high to low
dB
***********************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303
Tel: [phone]
Fax: [phone]
E-mail: [e-mail] http: // www.optoway.com.tw 1/1/2008 V3.0