XPS-4385W-D200G Datasheet, PDF (1/11 Pages) Optoway Technology Inc – 8.5 Gbps/ 80 km / 50 GHz DWDM XFP Single-Mode Optical Transceiver for 8G FC Applications

Optoway
1
XPS-4385W-DXXXG
***********************************************************************************************************************************************************************
XPS-4385W-DXXXG
(RoHS Compliant)
8.5 Gbps/ 80 km / 50 GHz DWDM XFP Single-Mode Optical Transceiver for 8G FC Applications
**********************************************************************************************************************************************************************
FEATURES
DESCRIPTION
l Up to 8.5 Gb/s Bi-directional Data Link
XPS-4385W-DXXXG series multi-rate 8G XFP
l Complaint to XFP MSA
transceiver is designed for serial optical data
l Compliance with Fibre Channel FC-PI-4 800-SM-LL-V
l Compliant with 4G and 2G Fibre Channel
l SFF-8472 Digital Diagnostic Function
l Maximum Link Length of 80 km
l Temperature-stabilized DWDM EML Transmitter
l 50 GHz ITU Grid, C Band
l AC/AC Coupling according to MSA
l 2-Wire Interface for Integrated Digital Diagnostic
communications such as 8G Fiber Channel. It supports the
8.5Gbps transmission on 9/125 µm SMF.
This module is designed for single mode fiber and
operates at a nominal wavelength of 50GHz ITU Grid, C
Band DWDM wavelength. The transmitter section consists
of a temperature-stabilized DWDM electrical-modulated
laser (EML), driver and signal conditioner. The receiver
section incorporates an avalanche photodiode integrated
Monitoring
l XFI Loopback Mode
l No Reference Clock Required
l Power Dissipation < 3.5 W
l +3.3 V & 5 V Power Supply
l RoHS 6/6 Compliant
l 0 to 70^oC Operating
l Duplex LC Connector
with a trans-impedance preamplifier (TIA) and signal
conditioner.
The module is with the XFP 30-pin connector to allow
hot plug capability. Integrated Tx and Rx signal conditioners
provide high jitter-tolerance for full XFI compliance and no
external reference clock required. The internally ac coupled
high speed serial I/O simplifies interfacing to external
circuitry. Only single 3.3V power supply is needed. The
APPLICATIONS
optical output can be disabled by LVTTL logic high-level
input of TX_DIS. Loss of signal (RX_LOS) output is
l Multi-rate 8x/4x/2x Fiber Channel
provided to indicate the loss of an input optical signal of
receiver.
STANDARD
l Compliant with XFP MSA
l Compliant with 8G FC
A serial EEPROM in the transceiver allows the user to
access transceiver digital diagnostic monitoring and
configuration data via the 2-wire XFP Management
Interface. This interface uses a single address, A0h, with a
LASER SAFETY
This transceiver is a Class 1 laser product. It complies with
IEC-60825 and FDA 21 CFR 1040.10 and 1040.11. The
memory map divided into a lower and upper area. Basic
digital diagnostic data is held in the lower area while specific
data is held in a series of tables in the high memory area.
transceiver must be operated within the specified
temperature and voltage limits. The optical ports of the
module shall be terminated with an optical connector or with
a dust plug.
**********************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303
Tel: [phone]
Fax: [phone]
E-mail: [e-mail] http: // www.optoway.com.tw 9/1/2012 V2.0