XPS-4140WG Datasheet, PDF (1/9 Pages) Optoway Technology Inc – 8.5Gb/s 1310 nm XFP Single-Mode Optical Transceiver for 8G FC Applications

Optoway
1
XPS-4140WG
***********************************************************************************************************************************************************************
XPS-4140WG / XPS-4140BWG / XPS-4140AWG
(RoHS Compliant)
8.5Gb/s 1310 nm XFP Single-Mode Optical Transceiver for 8G FC Applications
**********************************************************************************************************************************************************************
FEATURES
DESCRIPTION
l Up to 8.5 Gb/s Bi-directional Data Link
l Complaint to XFP MSA
l Compliance with Fibre Channel FC-PI-4 800-SM-LL-L
l Compliant with 4G and 2G Fibre Channel
l SFF-8472 Digital Diagnostic Function
l 1310 nm DFB LD Transmitter
l AC/AC Coupling according to MSA
l Distance up to 40 km
l 2-Wire Interface for Integrated Digital Diagnostic
XPS-4140WG series multi-rate 8G XFP transceiver is
designed for serial optical data communications such as 8G
Fiber Channel. It supports the 8.5Gbps transmission on
9/125 µm SMF.
The transceiver consists of two sections: The transmitter
section consists of a directly modulated 1310 nm multiple
quantum well DFB laser, driver and signal conditioner. The
receiver section incorporates a PIN photodiode integrated
with a trans-impedance preamplifier (TIA) and signal
Monitoring
l XFI Loopback Mode
l No reference clock required
l Low Power Dissipation < 2W
l Only Required +3.3 V Power Supply
l RoHS 6/6 Compliant
l 0 to 70^oC Operating: XPS-4140WG
l -10 to 85^oC Operating: XPS-4140BWG
l -40 to 85^oC Operating: XPS-4140AWG
l Duplex LC Connector
conditioner.
The module is with the XFP 30-pin connector to allow
hot plug capability. Integrated Tx and Rx signal conditioners
provide high jitter-tolerance for full XFI compliance and no
external reference clock required. The internally ac coupled
high speed serial I/O simplifies interfacing to external
circuitry. Only single 3.3V power supply is needed. The
optical output can be disabled by LVTTL logic high-level
input of TX_DIS. Loss of signal (RX_LOS) output is
provided to indicate the loss of an input optical signal of
APPLICATIONS
receiver.
A serial EEPROM in the transceiver allows the user to
l Multi-rate 8x/4x/2x Fiber Channel
access transceiver digital diagnostic monitoring and
configuration data via the 2-wire XFP Management
STANDARD
l Compliant with XFP MSA
l Compliant with 8G FC
Interface. This interface uses a single address, A0h, with a
memory map divided into a lower and upper area. Basic
digital diagnostic data is held in the lower area while specific
data is held in a series of tables in the high memory area.
LASER SAFETY
This transceiver is a Class 1 laser product. It complies with
IEC-60825 and FDA 21 CFR 1040.10 and 1040.11. The
transceiver must be operated within the specified
temperature and voltage limits. The optical ports of the
module shall be terminated with an optical connector or with
a dust plug.
ORDER INFORMATION
P/No.
Bit Rate
(Gb/s)
XPS-4140WG
XPS-4140BWG
XPS-4140AWG
8 /4 /2
8 /4 /2
8 /4 /2
Distance
(km)
40
40
40
Wavelength
(nm)
1310 DFB
1310 DFB
1310 DFB
Package
XFP with DMI
XFP with DMI
XFP with DMI
Connector
LC
LC
LC
Temp
(^oC)
0 to 70
-10 to 85
-40 to 85
RoHS
Compliant
Yes
Yes
Yes
**********************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303
Tel: [phone]
Fax: [phone]
E-mail: [e-mail] http: // www.optoway.com.tw 2008/5/1 V1.0