XPS-2381MW-D21G Datasheet, PDF (1/10 Pages) Optoway Technology Inc – 10G Multirate / 80 km / 100 GHz DWDM XFP Single-Mode Optical Transceiver

Optoway
1
XPS-2381MW-DXXG
***********************************************************************************************************************************************************************
XPS-2381MW-DXXG
(RoHS Compliant)
10G Multirate / 80 km / 100 GHz DWDM XFP Single-Mode Optical Transceiver
**********************************************************************************************************************************************************************
FEATURES
DESCRIPTION
l Supports 9.95 Gbps to 11.1Gbps
XPS-2381MW-DXXG series DWDM transceiver is
l Complaint with XFP MSA
designed for single-mode fibre serial optical data
l Compliant with XFI 10G Serial Electrical Interface
l Maximum Link Length of 80 km
l Temperature-stabilized DWDM EML Transmitter
l 100 GHz ITU Grid, C Band
l 2-Wire Interface for Integrated Digital Diagnostic
communications such as
10G SONET/SDH,
10GBASE-ZR/ZW Ethernet and 10G Fibre Channel.
This module is designed for single mode fiber and
operates at a nominal wavelength of 100GHz ITU Grid, C
Band DWDM wavelength. The transmitter section consists
Monitoring
l XFI Loopback Mode
l No reference Clock required
l Power Dissipation < 3.5 W
l Dual 5V and +3.3 V Power Supply
l RoHS-6 Compliant
l -5 to 70^oC Case Operating Temperature
of a temperature-stabilized DWDM electrical-modulated
laser (EML), driver and signal conditioner. The receiver
section incorporates an avalanche photodiode integrated
with a trans-impedance preamplifier (TIA) and signal
conditioner.
The module is with the XFP 30-pin connector to allow
hot plug capability. Integrated Tx and Rx signal conditioners
APPLICATIONS
provide high jitter-tolerance for full XFI compliance and no
external reference clock required. The internally ac coupled
l DWDM 10Gb/s SONET/SDH ITU-T G.698.1
l DWDM 10 Gb/s SONET/SDH with ITU-T G.709
l DWDM 80km 10G Etherent
l DWDM 80km 10G Fibre Channel
l DWDM 80km 10G Ethernet with FEC
high speed serial I/O simplifies interfacing to external
circuitry. Dual 5V and 3.3V power supply are used. The
optical output can be disabled by LVTTL logic high-level
input of TX_DIS. Loss of signal (RX_LOS) output is
provided to indicate the loss of an input optical signal of
LASER SAFETY
receiver.
A serial EEPROM in the transceiver allows the user to
This single-mode transceiver is a Class 1 laser product. It
complies with IEC-60825 and FDA 21 CFR 1040.10 and
1040.11. The transceiver must be operated within the
specified temperature and voltage limits. The optical ports
of the module shall be terminated with an optical connector
or with a dust plug.
access transceiver digital diagnostic monitoring and
configuration data via the 2-wire XFP Management
Interface. This interface uses a single address, A0h, with a
memory map divided into a lower and upper area. Basic
digital diagnostic data is held in the lower area while specific
data is held in a series of tables in the high memory area.
**********************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303
Tel: [phone]
Fax: [phone]
E-mail: [e-mail] http: // www.optoway.com.tw 7/1/2010 V1.0