XPS-2380MWG Datasheet, PDF (1/9 Pages) Optoway Technology Inc – 80km / 1550 nm / 10G Multirate XFP Single-Mode Optical Transceiver

Optoway
1
XPS-2380MWG
***********************************************************************************************************************************************************************
XPS-2380MWG
(RoHS Compliant)
80km / 1550 nm / 10G Multirate XFP Single-Mode Optical Transceiver
**********************************************************************************************************************************************************************
FEATURES
DESCRIPTION
l Support 9.95 Gbps to 11.1 Gbps
l Complaint with XFP MSA
l Compliant with XFI 10G Serial Electrical Interface
l Maximum Link Length of 80 km
l Temperature-stabilized 1550 nm 1600ps/nm EML
XPS-2380MWG series transceiver is designed for
single-mode fibre serial optical data communications such as
SONET OC-192 / SDH STM-64, 10G Ethernet
10GBASE-ER/EW and 10G Fibre Channel.
The transceiver consists of two sections: The transmitter
Transmitter
l 2-Wire Interface for Integrated Digital Diagnostic
section consists of a temperature-stabilized 1550 nm
electrical-modulated laser (EML), driver and signal
Monitoring
l No reference Clock required
l Power Dissipation < 3.5 W
l +3.3V and + 5V Power Supply
l RoHS-6 Compliant
l -5 to 70^oC Case Operating Temperature
conditioner. The receiver section incorporates a PIN
photodiode integrated with a trans-impedance preamplifier
(TIA) and signal conditioner.
The module is with the XFP 30-pin connector to allow
hot plug capability. Integrated Tx and Rx signal conditioners
provide high jitter-tolerance for full XFI compliance and no
APPLICATIONS
external reference clock required. The internally ac coupled
high speed serial I/O simplifies interfacing to external
l SONET OC-192 / SDH STM-64
circuitry. +5V and +3.3V power supplies are needed. The
ITU-T G.959.1 P1L1-2D2
l SONET OC-192 / SDH STM-64 with ITU-T G.709
l 10GBASE-ZR / ZW 80 km 10G Ethernet
l Extended 80 km 10G Fibre Channel
l 80 km 10G Ethernet with ITU-T G.709 FEC
optical output can be disabled by LVTTL logic high-level
input of TX_DIS. Loss of signal (RX_LOS) output is
provided to indicate the loss of an input optical signal of
receiver.
A serial EEPROM in the transceiver allows the user to
access transceiver digital diagnostic monitoring and
LASER SAFETY
configuration data via the 2-wire XFP Management
This single-mode transceiver is a Class 1 laser product. It
complies with IEC-60825 and FDA 21 CFR 1040.10 and
1040.11. The transceiver must be operated within the
specified temperature and voltage limits. The optical ports
Interface. This interface uses a single address, A0h, with a
memory map divided into a lower and upper area. Basic
digital diagnostic data is held in the lower area while specific
data is held in a series of tables in the high memory area.
of the module shall be terminated with an optical connector
or with a dust plug.
ORDER INFORMATION
P/No.
XPS-2380MWG
Bit Rate
(Gb/s)
9.95 – 11.1
10G
Multirate*
Distance
(km)
80
Wavelength
(nm)
1550 EML
Package
XFP with DMI
Case Temp
(^oC)
-5 to 70
*: multirate for SONET OC-192 IR2, OC-192 IR-3, 10GBASE-ER/EW, 10G Fibre Channel, ITU-T G.709,
10GBASE-ER/EW + FEC
RoHS
Compliant
Yes
Absolute Maximum Ratings
Parameter
Symbol
Min
Storage Temperature
Tstg
-40
Operating Case Temperature
Topr
-5
Relative Humidity
RH
0
Power Supply Voltage (5V)
Vcc5
-0.5
Power Supply Voltage (3.3V)
V_CC3
-0.5
Receiver Input Optical Power
Mip
Max
85
70
85
6.0
3.6
-4
Units
o_C
o_C
%
V
V
dBm
Notes
Non condensing
Received average power
**********************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303
Tel: [phone]
Fax: [phone]
E-mail: [e-mail] http: // www.optoway.com.tw 8/1/2008 V1.0