XPS-2360WG Datasheet, PDF (1/9 Pages) Optoway Technology Inc – 10Gbps / 60km / 1550 nm XFP Single-Mode Optical Transceiver for 10GbE / 10G FC

Optoway
1
XPS-2360WG
***********************************************************************************************************************************************************************
XPS-2360WG
(RoHS Compliant)
10Gbps / 60km / 1550 nm XFP Single-Mode Optical Transceiver for 10GbE / 10G FC
**********************************************************************************************************************************************************************
FEATURES
DESCRIPTION
z Support 9.95 Gbps to 10.5 Gbps
z Complaint with XFP MSA
z Compliant with XFI 10G Serial Electrical Interface
z Maximum Link Length of 60 km
z Temperature-stabilized 1550 nm EML Transmitter
z 2-Wire Interface for Integrated Digital Diagnostic
XPS-2360WG series transceiver is designed for
single-mode fibre serial optical data communications such as
10G Ethernet 10GBASE-ER/EW and 10G Fibre Channel.
The transceiver consists of two sections: The transmitter
section consists of a temperature-stabilized 1550 nm
electrical-modulated laser (EML), driver and signal
Monitoring
z XFI Loopback Mode
z No reference Clock required
z Power Dissipation < 3.5 W
z Dual 5V and +3.3 V Power Supply
z RoHS-6 Compliant
z -5 to 70^oC Case Operating Temperature
conditioner. The receiver section incorporates a PIN
photodiode integrated with a trans-impedance preamplifier
(TIA) and signal conditioner.
The module is with the XFP 30-pin connector to allow
hot plug capability. Integrated Tx and Rx signal conditioners
provide high jitter-tolerance for full XFI compliance and no
external reference clock required. The internally ac coupled
high speed serial I/O simplifies interfacing to external
APPLICATIONS
z 10GBASE-ER/EW
z 60 km 10G Fibre Channel
circuitry. Dual 5V and 3.3V power supplies are needed. The
optical output can be disabled by LVTTL logic high-level
input of TX_DIS. Loss of signal (RX_LOS) output is
provided to indicate the loss of an input optical signal of
LASER SAFETY
This single-mode transceiver is a Class 1 laser product. It
complies with IEC-60825 and FDA 21 CFR 1040.10 and
1040.11. The transceiver must be operated within the
specified temperature and voltage limits. The optical ports
of the module shall be terminated with an optical connector
or with a dust plug.
receiver.
A serial EEPROM in the transceiver allows the user to
access transceiver digital diagnostic monitoring and
configuration data via the 2-wire XFP Management
Interface. This interface uses a single address, A0h, with a
memory map divided into a lower and upper area. Basic
digital diagnostic data is held in the lower area while specific
data is held in a series of tables in the high memory area.
ORDER INFORMATION
P/No.
Bit Rate
(Gb/s)
XPS-2360WG
9.95 – 10.5
10GBASE
ER/EW
Distance
(km)
60
Wavelength
(nm)
1550 EML
Package
XFP with DMI
Case Temp
(^oC)
-5 to 70
RoHS
Compliant
Yes
Absolute Maximum Ratings
Parameter
Symbol
Min
Storage Temperature
Tstg
-40
Operating Case Temperature
Topr
-5
Relative Humidity
RH
0
Power Supply Voltage (5V)
Vcc5
-0.5
Power Supply Voltage (3.3V)
V_CC3
-0.5
Receiver Input Optical Power
Mip
Max
Units
Notes
85
o_C
70
o_C
85
%
Non condensing
6.0
V
3.6
V
4
dBm Received average power
**********************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303
Tel: [phone]
Fax: [phone]
E-mail: [e-mail] http: // www.optoway.com.tw 8/1/2008 V1.0