XPS-2340MWG_09 Datasheet, PDF (1/9 Pages) Optoway Technology Inc – 40km / 1550 nm / 10G Multirate XFP Single-Mode Optical Transceiver

Optoway
1
XPS-2340MWG
***********************************************************************************************************************************************************************
XPS-2340MWG / XPS-2340BMWG / XPS-2340AMWG
(RoHS Compliant)
40km / 1550 nm / 10G Multirate XFP Single-Mode Optical Transceiver
**********************************************************************************************************************************************************************
FEATURES
DESCRIPTION
l Support 9.95 Gbps to 11.3 Gbps
l Complaint with XFP MSA
l Compliant with XFI 10G Serial Electrical Interface
l Maximum Link Length of 40 km
l Temperature-stabilized 1550 nm 800ps/nm EML
XPS-2340MWG series transceiver is designed for
single-mode fibre serial optical data communications such as
SONET OC-192 / SDH STM-64, 10G Ethernet
10GBASE-ER/EW and 10G Fibre Channel.
The transceiver consists of two sections: The transmitter
Transmitter
l 2-Wire Interface for Integrated Digital Diagnostic
section consists of a temperature-stabilized 1550 nm
electrical-modulated laser (EML), driver and signal
Monitoring
l XFI Loopback Mode
l No reference Clock required
l Power Dissipation < 3.5 W
l Dual 5V and +3.3 V Power Supply
l RoHS-6 Compliant
l -5 to 70^oC Operating: XPS-2340MWG
l -5 to 85^oC Operating: XPS-2340BMWG
l -40 to 85^oC Operating: XPS-2340AMWG
conditioner. The receiver section incorporates a PIN
photodiode integrated with a trans-impedance preamplifier
(TIA) and signal conditioner.
The module is with the XFP 30-pin connector to allow
hot plug capability. Integrated Tx and Rx signal conditioners
provide high jitter-tolerance for full XFI compliance and no
external reference clock required. The internally ac coupled
high speed serial I/O simplifies interfacing to external
circuitry. Dual 5V and 3.3V power supply is needed. The
APPLICATIONS
optical output can be disabled by LVTTL logic high-level
input of TX_DIS. Loss of signal (RX_LOS) output is
l SONET OC-192 IR-2
provided to indicate the loss of an input optical signal of
SDH STM S-64.2b
receiver.
SONET OC-192 IR-3
A serial EEPROM in the transceiver allows the user to
SDH STM S-64.3b
access transceiver digital diagnostic monitoring and
ITU-T G.709
l 10GBASE-ER / EW
configuration data via the 2-wire XFP Management
Interface. This interface uses a single address, A0h, with a
10GBASE-ER/EW + FEC
l 40 km 10G Fibre Channel
40 km 10G Fibre Channel + FEC
memory map divided into a lower and upper area. Basic
digital diagnostic data is held in the lower area while specific
data is held in a series of tables in the high memory area.
LASER SAFETY
This single-mode transceiver is a Class 1 laser product. It
complies with IEC-60825 and FDA 21 CFR 1040.10 and
1040.11. The transceiver must be operated within the
specified temperature and voltage limits. The optical ports
of the module shall be terminated with an optical connector
or with a dust plug.
ORDER INFORMATION
P/No.
Bit Rate
(Gb/s)
10G
Distance Wavelength
(km)
(nm)
Package
Case Temp
(^oC)
XPS-2340MWG
9.95 – 11.1 Multirate*
40
1550 EML XFP with DMI
-5 to 70
XPS-2340BMWG
9.95 – 11.1 Multirate*
40
1550 EML XFP with DMI
-5 to 85
XPS-2340AMWG
9.95 – 11.1 Multirate*
40
1550 EML XFP with DMI -40 to 85
*: multirate for SONET OC-192 IR2, OC-192 IR-3, 10GBASE-ER/EW, 10G Fibre Channel, ITU-T G.709,
10GBASE-ER/EW + FEC
RoHS
Compliant
Yes
Yes
Yes
**********************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303
Tel: [phone]
Fax: [phone]
E-mail: [e-mail] http: // www.optoway.com.tw 7/1/2009 V2.0