XPS-2110WG_07 Datasheet, PDF (1/9 Pages) Optoway Technology Inc – 10Gb/s 10km 1310 nm XFP Single-Mode Optical Transceiver for 10GbE / 10GFC

Optoway
1
XPS-2110WG
***********************************************************************************************************************************************************************
XPS-2110WG / XPS-2110BWG / XPS-2110AWG
(RoHS Compliant)
10Gb/s 10km 1310 nm XFP Single-Mode Optical Transceiver for 10GbE / 10GFC
**********************************************************************************************************************************************************************
FEATURES
or with a dust plug.
l Support 9.95 Gbps to 10.5 Gbps
DESCRIPTION
l Complaint with XFP MSA
XPS-2110WG series transceiver is designed for
l Compliant to IEEE 802.3ae 10GBASE-LR/LW
single-mode fibre serial optical data communications such as
l Compliant to 10GFC 1200-SM-LL-L
10G Ethernet 10GBASE-LR/LW and 10G Fibre Channel
l Compliant with XFI 10G Serial Electrical Interface
1200-SM-LL-L.
l Maximum Link Length of 10 km
The transceiver consists of two sections: The transmitter
l Uncooled 1310 nm DFB LD
section consists of a directly modulated uncooled 1310 nm
l 2-Wire Interface for Integrated Digital Diagnostic
DFB laser, driver and signal conditioner. The receiver
Monitoring
l XFI Loopback Mode
l No reference Clock required
l Only Required +3.3 V Power Supply
l Power Consumption < 2 W
l RoHS Compliant
l -5 to 70^oC Operating : XPS-2110WG
l -10 to 85^oC Operating : XPS-2110BWG
l -40 to 85^oC Operating : XPS-2110AWG
l Duplex LC Connector
section incorporates a PIN photodiode integrated with a
trans-impedance preamplifier (TIA) and signal conditioner.
The module is with the XFP 30-pin connector to allow
hot plug capability. Integrated Tx and Rx signal conditioners
provide high jitter-tolerance for full XFI compliance and no
external reference clock required. The internally ac coupled
high speed serial I/O simplifies interfacing to external
circuitry. Only single 3.3V power supply is needed. The
optical output can be disabled by LVTTL logic high-level
input of TX_DIS. Loss of signal (RX_LOS) output is
APPLICATIONS
provided to indicate the loss of an input optical signal of
receiver.
l 10GBASE-LR at 10.3125 Gb/s
l 10GBASE-LW at 9.953 Gb/s
l 10GFC at 10.51875 Gb/s
A serial EEPROM in the transceiver allows the user to
access transceiver digital diagnostic monitoring and
configuration data via the 2-wire XFP Management
Interface. This interface uses a single address, A0h, with a
LASER SAFETY
This single-mode transceiver is a Class 1 laser product. It
complies with IEC-60825 and FDA 21 CFR 1040.10 and
memory map divided into a lower and upper area. Basic
digital diagnostic data is held in the lower area while specific
data is held in a series of tables in the high memory area.
1040.11. The transceiver must be operated within the
specified temperature and voltage limits. The optical ports
of the module shall be terminated with an optical connector
ORDER INFORMATION
P/No.
Bit Rate
(Gb/s)
XPS-2110WG
XPS-2110BWG
XPS-2110AWG
9.95 – 10.52
9.95 – 10.52
9.95 – 10.52
10GBASE
LR/LW
LR/LW
LR/LW
Distance
(km)
10
10
10
Wavelength
(nm)
1310 DFB
1310 DFB
1310 DFB
Package
XFP with DMI
XFP with DMI
XFP with DMI
Case Temp
(^oC)
-5 to 70
-10 to 85
-40 to 85
RoHS
Compliant
Yes
Yes
Yes
Absolute Maximum Ratings
Parameter
Symbol
Min
Storage Temperature
Tstg
-40
Operating Case Temperature
Topr
-5
-10
-40
Relative Humidity
RH
0
Power Supply Voltage
V_CC3
0
Max
85
70
85
85
85
3.6
Units
o_C
o_C
%
V
Notes
XPS-2110WG
XPS-2110BWG
XPS-2110AWG
Non condensing
**********************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303
Tel: [phone]
Fax: [phone]
E-mail: [e-mail] http: // www.optoway.com.tw 2007/12/1 V3.0