XPS-2110WG Datasheet, PDF (1/8 Pages) Optoway Technology Inc – 10Gb/s 10km 1310 nm XFP Single-Mode Optical Transceiver for 10GbE / 10GFC

Optoway
1
XPS-2110WG
***********************************************************************************************************************************************************************
XPS-2110WG / XPS-2110BWG
(RoHS Compliant)
10Gb/s 10km 1310 nm XFP Single-Mode Optical Transceiver for 10GbE / 10GFC
**********************************************************************************************************************************************************************
FEATURES
DESCRIPTION
l Support 9.95 Gbps to 10.5 Gbps
l Complaint with XFP MSA
l Compliant to IEEE 802.3ae 10GBASE-LR/LW
l Compliant to 10GFC 1200-SM-LL-L
l Compliant with XFI 10G Serial Electrical Interface
l Maximum Link Length of 10 km
l Uncooled 1310 nm DFB LD
l 2-Wire Interface for Integrated Digital Diagnostic
XPS-2110WG series transceiver is designed for
single-mode fibre serial optical data communications such as
10G Ethernet 10GBASE-LR/LW and 10G Fibre Channel
1200-SM-LL-L.
The transceiver consists of two sections: The transmitter
section consists of a directly modulated uncooled 1310 nm
DFB laser, driver and signal conditioner. The receiver
section incorporates a PIN photodiode integrated with a
Monitoring
l No reference Clock required
l Only Required +3.3 V Power Supply
l Power Consumption < 2 W
l RoHS Compliant
l -5 to 70^oC Case Operating Temperature : XPS-2110WG
l -5 to 85^oC Case Operating Temperature : XPS-2110BWG
l Duplex LC Connector
trans-impedance preamplifier (TIA) and signal conditioner.
The module is with the XFP 30-pin connector to allow
hot plug capability. Integrated Tx and Rx signal conditioners
provide high jitter-tolerance for full XFI compliance and no
external reference clock required. The internally ac coupled
high speed serial I/O simplifies interfacing to external
circuitry. Only single 3.3V power supply is needed. The
optical output can be disabled by LVTTL logic high-level
APPLICATIONS
input of TX_DIS. Loss of signal (RX_LOS) output is
provided to indicate the loss of an input optical signal of
l 10GBASE-LR at 10.3125 Gb/s
l 10GBASE-LW at 9.953 Gb/s
l 10GFC at 10.51875 Gb/s
receiver.
A serial EEPROM in the transceiver allows the user to
access transceiver digital diagnostic monitoring and
configuration data via the 2-wire XFP Management
LASER SAFETY
This single-mode transceiver is a Class 1 laser product. It
complies with IEC-60825 and FDA 21 CFR 1040.10 and
1040.11. The transceiver must be operated within the
Interface. This interface uses a single address, A0h, with a
memory map divided into a lower and upper area. Basic
digital diagnostic data is held in the lower area while specific
data is held in a series of tables in the high memory area.
specified temperature and voltage limits. The optical ports
of the module shall be terminated with an optical connector
or with a dust plug.
ORDER INFORMATION
P/No.
Bit Rate
(Gb/s)
XPS-2110WG
XPS-2110BWG
9.95 – 10.52
9.95 – 10.52
10GBASE
LR/LW
LR/LW
Distance
(km)
10
10
Wavelength
(nm)
1310 DFB
1310 DFB
Package
XFP with DMI
XFP with DMI
Case Temp
(^oC)
-5 to 70
-5 to 85
RoHS
Compliant
Yes
Yes
Absolute Maximum Ratings
Parameter
Symbol
Min
Storage Temperature
Tstg
-40
Operating Case Temperature
Topr
-5
-5
Relative Humidity
Power Supply Voltage
RH
0
V_CC3
0
Max
85
70
85
85
3.6
Units
o_C
o_C
%
V
Notes
XPS-2110WG
XPS-2110BWG
Non condensing
**********************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303
Tel: [phone]
Fax: [phone]
E-mail: [e-mail] http: // www.optoway.com.tw 2/1/2007 V1.0