XPM-4100WG Datasheet, PDF (1/9 Pages) Optoway Technology Inc – 8.5Gb/s 850 nm XFP Multi-Mode Optical Transceiver for 8G FC Applications

Optoway
1
XPM-4100WG
***********************************************************************************************************************************************************************
XPM-4100WG / XPM-4100BWG / XPM-4100AWG
(RoHS Compliant)
8.5Gb/s 850 nm XFP Multi-Mode Optical Transceiver for 8G FC Applications
**********************************************************************************************************************************************************************
FEATURES
DESCRIPTION
l Up to 8.5 Gb/s Bi-directional Data Link
l Complaint to XFP MSA
l Compliant with 8G FC 800-M5/M6/M5E-LC-I
l Multirate for 8G / 4G / 2G FC
l Link Distance at 8.5 Gbd
XPM-4100WG series multi-rate 8G XFP transceiver is
designed for serial optical data communications such as 8G
Fiber Channel. It supports the 8.5Gbps transmission on both
50/125 µm and 62.5/125 µm MMF.
The transceiver consists of two sections: The transmitter
150 m links with OM3 MMF Cables
section consists of a directly modulated 850 nm VCSEL,
50 m links with OM2 MMF Cables
driver and signal conditioner. The receiver section
21 m links with OM1 MMF Cables
l 850 nm VCSEL Transmitter
l 2-Wire Interface for Integrated Digital Diagnostic
incorporates a PIN photodiode integrated with a
trans-impedance preamplifier (TIA) and signal conditioner.
The module is with the XFP 30-pin connector to allow
Monitoring
l XFI Loopback Mode
l No reference clock required
l Low Power Dissipation < 1.2W
l Only Required +3.3 V Power Supply
l RoHS Compliant
l 0 to 70^oC Operating: XPM-4100WG
l -10 to 85^oC Operating: XPM-4100BWG
l -40 to 85^oC Operating: XPM-4100AWG
l Duplex LC Connector
hot plug capability. Integrated Tx and Rx signal conditioners
provide high jitter-tolerance for full XFI compliance and no
external reference clock required. The internally ac coupled
high speed serial I/O simplifies interfacing to external
circuitry. Only single 3.3V power supply is needed. The
optical output can be disabled by LVTTL logic high-level
input of TX_DIS. Loss of signal (RX_LOS) output is
provided to indicate the loss of an input optical signal of
receiver.
A serial EEPROM in the transceiver allows the user to
APPLICATIONS
access transceiver digital diagnostic monitoring and
configuration data via the 2-wire XFP Management
l Multi-rate 8x/4x/2x Fiber Channel
Interface. This interface uses a single address, A0h, with a
memory map divided into a lower and upper area. Basic
STANDARD
l Compliant with XFP MSA
l Compliant with 8G FC
digital diagnostic data is held in the lower area while specific
data is held in a series of tables in the high memory area.
LASER SAFETY
This transceiver is a Class 1 laser product. It complies with
IEC-60825 and FDA 21 CFR 1040.10 and 1040.11. The
transceiver must be operated within the specified
temperature and voltage limits. The optical ports of the
module shall be terminated with an optical connector or with
a dust plug.
ORDER INFORMATION
P/No.
Bit Rate
(Gb/s)
XPM-4100WG
XPM-4100BWG
XPM-4100AWG
*LINK LENGTH
8 /4 /2
8 /4 /2
8 /4 /2
Distance
(m)
150/50/21*
150/50/21*
150/50/21*
Wavelength
(nm)
850
850
850
Package
XFP with DMI
XFP with DMI
XFP with DMI
Connector
LC
LC
LC
Temp
(^oC)
0 to 70
-10 to 85
-40 to 85
RoHS
Compliant
Yes
Yes
Yes
Data Rate / Standard
8.5 GBd
Fiber Type
62.5/125 µm MMF (OM1)
50 / 125 µm MMF (OM2)
50 / 125 µm MMF
50 / 125 µm MMF
50 / 125 µm MMF (OM3)
Model Bandwidth @ 850nm (MHz-km)
200
500
900
1500
2000
Distance Range (m)
0.5 to 21
0.5 to 50
0.5 to 90
0.5 to 120
0.5 to 150
**********************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303
Tel: [phone]
Fax: [phone]
E-mail: [e-mail] http: // www.optoway.com.tw 2009/11/1 V3.0