XPM-2101WG Datasheet, PDF (1/9 Pages) Optoway Technology Inc – 10Gb/s 1310 nm XFP Extended Multi-Mode Optical Transceiver for 10GbE-LRM Applications

Optoway
1
XPM-2101WG
***********************************************************************************************************************************************************************
XPM-2101WG
(RoHS Compliant)
10Gb/s 1310 nm XFP Extended Multi-Mode Optical Transceiver for 10GbE-LRM Applications
**********************************************************************************************************************************************************************
FEATURES
DESCRIPTION
z Support 10.3125 Gbps
z Complaint with XFP MSA
z Compliant to IEEE 802.3aq-2006 10GBASE-LRM
z Link Length from 0.5 to 300 m with OM1 MMF
z Link Length from 0.5 to 300 m with OM2 MMF
z Link Length from 0.5 to 300 m with OM3 MMF
z 1310 nm Transmitter
z 2-Wire Interface for Integrated Digital Diagnostic
XPM-2101WG series extended multi-mode 10G XFP
transceiver is designed for serial optical data
communications such as 10 GBASE-LRM. It supports the
10Gbps transmission on both 50/125 μm and 62.5/125 μm
MMF.
The transceiver consists of two sections: The transmitter
section consists of a directly modulated 1310 nm FP laser,
driver and signal conditioner. The receiver section
Monitoring
z No reference clock required
z Low Power Dissipation < 2.0 W
z Only Required +3.3 V Power Supply
z RoHS Compliant
z 0 to 70^oC Case Operating Temperature
z Duplex LC Connector
incorporates a PIN photodiode integrated with a
trans-impedance preamplifier (TIA) and signal conditioner.
The module is with the XFP 30-pin connector to allow
hot plug capability. Integrated Tx and Rx signal conditioners
provide high jitter-tolerance for full XFI compliance and no
external reference clock required. The internally ac coupled
high speed serial I/O simplifies interfacing to external
circuitry. Only single 3.3V power supply is needed. The
APPLICATIONS
z 10G Ethernet at 10.3125Gbps
optical output can be disabled by LVTTL logic high-level
input of TX_DIS. Loss of signal (RX_LOS) output is
provided to indicate the loss of an input optical signal of
STANDARD
z Compliant with XFP MSA
z Compliant with IEEE 802.3aq-2006
receiver.
A serial EEPROM in the transceiver allows the user to
access transceiver digital diagnostic monitoring and
configuration data via the 2-wire XFP Management
LASER SAFETY
This multi-mode transceiver is a Class 1 laser product. It
complies with IEC-60825 and FDA 21 CFR 1040.10 and
1040.11. The transceiver must be operated within the
Interface. This interface uses a single address, A0h, with a
memory map divided into a lower and upper area. Basic
digital diagnostic data is held in the lower area while specific
data is held in a series of tables in the high memory area.
specified temperature and voltage limits. The optical ports
of the module shall be terminated with an optical connector
or with a dust plug.
ORDER INFORMATION
P/No.
Bit Rate
(Gb/s)
Distance Wavelength
(m)
(nm)
Package
Connector
Temp
(^oC)
RoHS
Compliant
XPM-2101WG
10.3125
300*
1310
XFP with DMI
LC
0 to 70
Yes
*: see below table for transmission distance in MM fiber
Multimode Fiber Type**
ISO/IEC 11801:2002
Fiber Type
Operating Range
(m)
62.5 μm 160/500
62.5 μm 200/500
OM1
0.5 to 300
0.5 to 300
50 μm 500/500
50 μm 1500/500***
OM2
OM3
0.5 to 300
0.5 to 300
**: Each fiber type is identified by its core diameter followed by a pair of OFL bandwidth values separated by “/”. The OFL
bandwidths are in MHz-km and are for 850 nm and 1300nm respectively.
***: The OM3 fiber specification includes the 850 nm laser launch bandwidth in addition to the OFL bandwidth.
**********************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303
Tel: [phone]
Fax: [phone]
E-mail: [e-mail] http: // www.optoway.com.tw 1/12/2009 V2.0