XPM-2100WG_10 Datasheet, PDF (1/9 Pages) Optoway Technology Inc – 10Gb/s 850 nm XFP Multi-Mode Optical Transceiver for 10GbE / 10GFC Applications

Optoway
1
XPM-2100WG
***********************************************************************************************************************************************************************
XPM-2100WG / XPM-2100BWG / XPM-2100AWG
(RoHS Compliant)
10Gb/s 850 nm XFP Multi-Mode Optical Transceiver for 10GbE / 10GFC Applications
**********************************************************************************************************************************************************************
FEATURES
DESCRIPTION
l Support 9.95 Gbps to 10.5 Gbps
XPM-2100WG series multi-rate 10G XFP transceiver is
l Complaint with XFP MSA
designed for serial optical data communications such as 10
l Compliant to IEEE 802.3ae 10GBASE
l Compliant to 10GFC
l Link Length up to 300 m with OM3 MMF
l Link Length up to 82 m with OM2 MMF
l Link Length up to 33 m with OM1 MMF
l 850 nm VCSEL Transmitter
l 2-Wire Interface for Integrated Digital Diagnostic
Gigabit Ethernet and 10G Fiber Channel. It supports the
10Gbps transmission on both 50/125 µm and 62.5/125 µm
MMF.
The transceiver consists of two sections: The transmitter
section consists of a directly modulated 850 nm VCSEL,
driver and signal conditioner. The receiver section
incorporates a PIN photodiode integrated with a
Monitoring
l No reference clock required
l Low Power Dissipation < 1.2W
l Only Required +3.3 V Power Supply
l RoHS Compliant
l -5 to 70^oC Operating : XPM-2100WG
l -10 to 85^oC Operating : XPM-2100BWG
l -40 to 85^oC Operating : XPM-2100AWG
l Duplex LC Connector
trans-impedance preamplifier (TIA) and signal conditioner.
The module is with the XFP 30-pin connector to allow
hot plug capability. Integrated Tx and Rx signal conditioners
provide high jitter-tolerance for full XFI compliance and no
external reference clock required. The internally ac coupled
high speed serial I/O simplifies interfacing to external
circuitry. Only single 3.3V power supply is needed. The
optical output can be disabled by LVTTL logic high-level
input of TX_DIS. Loss of signal (RX_LOS) output is
APPLICATIONS
provided to indicate the loss of an input optical signal of
receiver.
l 10G Ethernet at 10.3125Gbps
l 10G Ethernet at 9.953 Gbps
l 10GFC at 10.51875 Gbps
A serial EEPROM in the transceiver allows the user to
access transceiver digital diagnostic monitoring and
configuration data via the 2-wire XFP Management
Interface. This interface uses a single address, A0h, with a
STANDARD
l Compliant with XFP MSA
l Compliant with IEEE 802.3ae-2002
l Compliant with 10GFC
memory map divided into a lower and upper area. Basic
digital diagnostic data is held in the lower area while specific
data is held in a series of tables in the high memory area.
LASER SAFETY
This transceiver is a Class 1 laser product. It complies with
IEC-60825 and FDA 21 CFR 1040.10 and 1040.11. The
transceiver must be operated within the specified
temperature and voltage limits. The optical ports of the
module shall be terminated with an optical connector or with
a dust plug.
ORDER INFORMATION
P/No.
Bit Rate
(Gb/s)
Distance Wavelength
(m)
(nm)
Package
Connector
Temp
(^oC)
RoHS
Compliant
XPM-2100WG
9.95 – 10.52 300/82/33*
850
XFP with DMI
LC
0 to 70
Yes
XPM-2100BWG
9.95 – 10.52 300/82/33*
850
XFP with DMI
LC
-10 to 85
Yes
XPM-2100AWG
9.95 – 10.52 300/82/33*
850
XFP with DMI
LC
-40 to 85
Yes
*: Distance up to 300 m on 50/125 OM3 MMF, up to 82 m for 50/125 mm MMF with model bandwidth 500 MHz-km at 850
nm, & up to 33 m for 62.5/125 mm MMF with model bandwidth 200 MHz-km at 850 nm.
**********************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303
Tel: [phone]
Fax: [phone]
E-mail: [e-mail] http: // www.optoway.com.tw 2010/7/1 V3.0