OP235_14 Datasheet, PDF (3/6 Pages) OPTEK Technologies – Hermetic Infrared Emitting Diode

Hermetic Infrared Emitting Diode
OP230 Series
Absolute Maximum Ratings (T_A=25°C unless otherwise noted)
Storage Temperature Range
Operating Temperature Range
Reverse Voltage
Continuous Forward Current
Peak Forward Current
Lead Soldering Temperature [1/16 inch (1.6 mm) from case for 5 seconds with soldering iron]
Power Dissipation
-65^o C to +150^o C
-65^o C to +125^o C
2.0 A
100 mA
10.0 A
260° C⁽¹⁾⁽²⁾
200 mW⁽³⁾
Electrical Characteristics (T_A = 25°C unless otherwise noted)
SYMBOL
PARAMETER
MIN TYP MAX UNITS
TEST CONDITIONS
Input Diode
E_E(APT)
P_O
V_F
I_R
λ_P
β
∆λ_P /∆T
θ_HP
t_r
t_f
Apertured Radiant Incidence
OP231
OP232
OP233
OP234
OP235
OP231W
OP232W
OP233W
OP234W
OP235W
Radiant Power Output
OP231
OP232
OP233
Forward Voltage
Reverse Current
Wavelength at Peak Emission
OP231, OP232, OP233
OP234, OP235
Spectral Bandwidth between Half Power
Points
Spectral Shift with Temperature
Emission Angle at Half Power Points
OP231 - OP235
OP231W - OP231W
Output Rise Time
Output Fall Time
1.5 -
-
OP231 Series
2.0
3.0
-
-
6.0
-
mW/cm²
I_F = 100 mA^{(3 )(4)}
Aperture = 0.250”
5.0 -
-
Distance = 1.429”
6.0 -
-
1.5 -
-
OP231W Series
3.5
5.0
5.0
-
-
-
7.0
-
-
mW/cm²
I_F = 100 mA^{(3 )(4)}
Aperture = 0.250”
6.0 -
-
Distance = 0.466”
- 6.0 -
- 8.0 -
- 10.0 -
mW ^{IF = 100 mA(3 )(4)}
-
- 2.0
V
I_F = 100 mA ⁽³⁾
-
- 100 µA V_R= 2.0 V
- 890 -
- 850 -
-
80
-
- +0.30 -
nm I_F = 10 mA
nm I_F = 10 mA
nm/°C I_F = Constant
-
-
18
50
-
-
Degree I_F = 100 mA
- 500 -
- 250 -
ns _{IF(PK)=100 mA, PW=10 µs, and}
ns ^D.C.=10.0%
Notes:
1. RMA flux is recommended. Duration can be extended to 10 seconds maximum when flow soldering.
2. Derate linearly 2.0 mW/° C above 25° C.
3. Measurement made with 100 µs pulse measured at the trailing edge of the pulse with a duty cycle of 0.1% and an I_F = 100 mA.
4. For the OP231 series, E_E(APT) is a measurement of the average radiant intensity within the cone formed by the measurement surface,
a radius of 1.429” (36.30 mm) measured from the lens side of the tab to the sensing surface and a sensing surface of 0.250” (6.35
mm) in diameter forming a 10° cone. For the OP231W series, E_E(APT) is a measurement of the average radiant intensity within the
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: [phone] or [phone]
FAX: [phone] [e-mail] www.optekinc.com
Issue A .2 01/09
Page 3 of 6