OP168F Datasheet, PDF (3/6 Pages) OPTEK Technologies – Plastic Infrared Emitting Diode

Plastic Infrared Emitting Diode
OP168F, OP169, OP268F, OP269 Series
Absolute Maximum Ratings (T_A=25°C unless otherwise noted)
Storage and Operating Temperature Range
-40^o C to +100^o C
Reverse Voltage
2.0 V
Continuous Forward Current
50 mA
Peak Forward Current (1 μs pulse width, 300 pps)
OP168, OP169, OP268, OP269 (A, B, C)
OP268FPS
Lead Soldering Temperature [1/16 inch (1.6 mm) from case for 5 seconds with soldering iron]⁽¹⁾
Power Dissipation⁽²⁾
Electrical Characteristics (T_A = 25°C unless otherwise noted)
3.0 A
100 mA
260° C
100 mW
SYMBOL
PARAMETER
MIN TYP MAX UNITS
TEST CONDITIONS
Input Diode
Apertured Radiant Incidence
OP168FA
OP168FB
OP168FC
0.48 -
-
0.43 - 0.73
0.27 -
-
E_E
(3)
(APT)
OP169A
OP169B
OP169C
OP268FA
OP268FB
OP268FC
OP268FPS
OP269A
OP269B
OP269C
Forward Voltage
V_F
OP168, OP169
OP268, OP269
OP268FPS
Reverse Current
I_R
OP168, OP169, OP268, OP269
OP268FPS
Wavelength at Peak Emission
λ_P
OP168, OP169
OP268, OP269
OP268FPS
0.18 -
-
0.11
0.03
0.64
0.45
-
-
-
-
-
0.22
-
-
0.99
I_F = 20 mA
mW/cm^{2 Aperture = .081” dia.}
Distance = .400” from tip of lens to
aperture surface
0.36 -
-
0.10 - 0.90
-
0.58 -
-
0.42 - 0.82
0.34 -
-
-
-
-
-
1.40
1.50
V I_F = 20 mA
-
- 1.80
-
-
-
-
100
20
µA V_R= 2.0 V
- 935 -
- 890 -
- 850 -
nm I_F = 20 mA
Notes:
1. RMA flux is recommended. Duration can be extended to 10 seconds maximum when flow soldering. A maximum of 20 grams force
may be applied to the leads when soldering.
2. Derate linearly 1.33 mW/° C above 25° C.
3. For OP168 (FA, FB, FC) and OP268 (FA, FB, FC), E_E(APT) is a measurement of the average apertured radiant energy incident upon a
sensing area 0.081” (2.06 mm) in diameter perpendicular to and centered on the mechanical axis of the lens and 0.400” (10.16 mm)
from the measurement surface. For OP169 (A, B, C) and OP269 (A, B, C), E_E(APT) is a measurement of the average apertured radiant
energy incident upon a sensing area 0.180” (4.57 mm) in diameter perpendicular to and centered on the mechanical axis of the lens
and 0.653” (16.6 mm) from the lens tip. NOTE: E_E(APT) is a measurement of the average radiant intensity within the cone formed by
the above conditions. E_E(APT) is not necessarily uniform within the measured area.
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: [phone] or [phone]
FAX: [phone] [e-mail] www.optekinc.com
Issue A 06/07
Page 3 of 6