CS1089 Datasheet, PDF (9/12 Pages) ON Semiconductor – Vacuum Fluorescent Display Tube Driver

SCALE 1:1
–L–
CS1089
PACKAGE DIMENSIONS
PLCC–44
FN SUFFIX
CASE 777–02
ISSUE C
–N–
Y BRK ^D
B 0.007(0.180) ^M T L-M ^S N ^S
U 0.007(0.180) ^M T L-M ^S N ^S
Z
–M–
V
44
1
WD
X
VIEW D–D
G1
0.010 (0.25) S T L-M S N S
A
0.007(0.180) M T L-M S N S
R
Z
0.007(0.180) M T L-M S N S
C
E
G
G1
0.010 (0.25) S T L-M S N S
J
0.004 (0.10)
–T– SEATING
PLANE
VIEW S
H
0.007(0.180) M T L-M S N S
K1
K
F
0.007(0.180) M T L-M S N S
VIEW S
NOTES:
1. DATUMS -L-, -M-, AND -N- ARE DETERMINED
WHERE TOP OF LEAD SHOULDER EXITS
PLASTIC BODY AT MOLD PARTING LINE.
2. DIMENSION G1, TRUE POSITION TO BE
MEASURED AT DATUM -T-, SEATING PLANE.
3. DIMENSIONS R AND U DO NOT INCLUDE MOLD
FLASH. ALLOWABLE MOLD FLASH IS 0.010
(0.25) PER SIDE.
4. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
5. CONTROLLING DIMENSION: INCH.
6. THE PACKAGE TOP MAY BE SMALLER THAN
THE PACKAGE BOTTOM BY UP TO 0.012
(0.300). DIMENSIONS R AND U ARE
DETERMINED AT THE OUTERMOST
EXTREMES OF THE PLASTIC BODY
EXCLUSIVE OF MOLD FLASH, TIE BAR BURRS,
GATE BURRS AND INTERLEAD FLASH, BUT
INCLUDING ANY MISMATCH BETWEEN THE
TOP AND BOTTOM OF THE PLASTIC BODY.
7. DIMENSION H DOES NOT INCLUDE DAMBAR
PROTRUSION OR INTRUSION. THE DAMBAR
PROTRUSION(S) SHALL NOT CAUSE THE H
DIMENSION TO BE GREATER THAN 0.037
(0.940). THE DAMBAR INTRUSION(S) SHALL
NOT CAUSE THE H DIMENSION TO BE
SMALLER THAN 0.025 (0.635).
INCHES
MILLIMETERS
DIM MIN MAX MIN MAX
A 0.685 0.695 17.40 17.65
B 0.685 0.695 17.40 17.65
C 0.165 0.180 4.20 4.57
E 0.090 0.110 2.29 2.79
F 0.013 0.019 0.33 0.48
G
0.050 BSC
1.27 BSC
H 0.026 0.032 0.66 0.81
J 0.020 --- 0.51 ---
K 0.025 --- 0.64 ---
R 0.650 0.656 16.51 16.66
U 0.650 0.656 16.51 16.66
V 0.042 0.048 1.07 1.21
W 0.042 0.048 1.07 1.21
X 0.042 0.056 1.07 1.42
Y --- 0.020 --- 0.50
Z
2_{_} 10_{_} 2_{_} 10_{_}
G1 0.610 0.630 15.50 16.00
K1 0.040 --- 1.02 ---
http://onsemi.com
9