CS212 Datasheet, PDF (6/8 Pages) Cherry Semiconductor Corporation – Security Detector Serial-Addressable Receiver/Transmitter

Functional Description: continued
WRITE
A0 A1 A2 A3 A4 PA BIT D0 D1 PD
0 1 00 011 1 0 1
0 1 00 0 1 1 1 0 1
Data Parity
OUT 1
OUT 0
"1" for Write
Add Parity
A4=0 x 2⁴ = 0
A3=0 x 2³ = 0
A2=0 x 2² = 0
A1=1 x 2¹ = 2
A0=0 x 2⁰ = 0
Binary = #2
TYPICAL WRITE WORD:
Assume CS212 #2 is to be updated so that OUT0=1 and
OUT1=0.
INPUTS:
1. Address inputs: Pin#'s 2,3,4,5,6.
The CS212 has 5 address inputs which decide what
address code it will respond to. Their thresholds are
approximately 1/2 V_DD and draw less than 20µA. The
inputs should be grounded for Logic "0" and tied to V_DD
(PIN 12) through a 10K resistor for Logic "1". The resis-
tor is necessary for non-destruction of the IC with 28V
applied to the line.
2. Data Inputs: Pin#'s 7,8.
IN0 and IN1 (Pins 8 and 7) are digital inputs and are
similar to the address inputs in that they have a thresh-
old of approximately 1/2 V_DD. When the CS212 is unad-
dressed, these inputs draw less than 20µA. When the
circuit powers up, IN0 and IN1 typically source 400µA.
3. Detector Loop: Pin #'s 13, 14.
IN2 and IN3 can be used together to form a detector
loop. When used, the outputs are connected together
through a window foil and a diode. These inputs will
generate a logic “1” at D1 on the line when the pins are
shorted or opened.
OUTPUTS
1. OUT0 and OUT1: Pin #'s 1, 16:
These outputs are updated according to the information
present during the write word.
2. DSR: Pin #15:
The DSR pin is a monitor of the clock signal for the on-
chip D flip flops, corresponding to OUT0 and OUT1. It
can be used to strobe data from OUT0 and OUT1 into
external circuitry connected to the CS212.
These three outputs can sink up to 1mA at 1.2V. They are
Darlington type open collector outputs.
OUT 0, OUT 1, DSR
LINE
DSR
The Edge is Present
When OUT 0 & OUT 1 are Updated.
3. Data Out: Pin #11:
The Data Out pin is used to transmit the status of IN0
and IN1 to the line. For Data=1, the line driver is off. For
Data=0, the line driver is turned on. This output is a sat-
urated switch capable of sinking 10mA DC at .4V and
50mA at 1V on a transient basis. The 50mA is needed to
discharge the line capacitance. A 150Ω resistor from the
line to Pin 11 limits the current into Pin 11 when the line
driver is on.
IN 1
IN 2
IN 3
Loop Status
DET.
1 When IN 1=1
T0 D, Online
Durning Read
1 When Loop
is Open or Shorted
When using IN2 and IN3, IN1 must be terminated to
V_DD through the 10K Resistor used for the address
inputs. When using IN1, IN2 and IN3 must be shorted
or opened.
4. Line Input: Pin #9
The line input is internally connected to two compara-
tors. These comparators separate the line signal into
clock and data. The line input will draw less than 16µA
of input current.
5. V_DD: Pin #12
The V_DD Pin provides power to the CS212 circuitry. The
line signal is externally rectified and filtered, then
applied to V_DD. The V_DD pin draws varying amounts of
current, depending upon the state of the CS212. (See
specification). The unaddressed current is less than
0.8mA.
The operating voltage range is 10V to 18V on Pin 12 of
the IC. This wide range is necessary because of losses in
the line and ripple on V_DD.
The circuit is designed to withstand 28V applied to the
line. This is to prevent the destruction of the IC and its
external components if the 2-wire cable is miswired.
6