NCV8537 Datasheet, PDF (5/16 Pages) ON Semiconductor – 500 mA High Accuracy Low Dropout Linear Regulator with Power Good Function

NCV8537
ELECTRICAL CHARACTERISTICS − 1.8 V
(V_out = 1.8 V typical, V_in = 2.9 V, T_A = −40C to +125C, unless otherwise noted, Note 2)
Characteristic
Symbol Min
Typ
Max
Unit
Output Voltage (Accuracy)
V_in = 2.9 V to 5.8 V, I_load = 0.1 mA to 500 mA, T_A = 25C
Output Voltage (Accuracy)
V_in = 2.9 V to 5.8 V, I_load = 0.1 mA to 500 mA, T_A = 0C to +85C
Output Voltage (Accuracy)
V_in = 2.9 V to 5.8 V, I_load = 0.1 mA to 500 mA, T_A = −40C to +125C
Minimum Input Voltage
Line Regulation
V_in = 2.9 V to 12 V, I_load = 0.1 mA
Load Regulation
V_in = 2.9 V, I_load = 0.1 mA to 500 mA
Dropout Voltage (See Figure 9)
I_load = 500 mA (Notes 3, 4)
I_load = 300 mA (Notes 3, 4)
I_load = 50 mA (Notes 3, 4)
Peak Output Current (See Figures 14 and 17)
Short Output Current (See Figure 14) V_in < 7 V, T_A = 25C
Thermal Shutdown / Hysteresis
Ground Current
In Regulation
I_load = 500 mA (Note 3)
I_load = 300 mA (Note 3)
I_load = 50 mA
I_load = 0.1 mA
V_out
V_out
V_out
V_inmin
Line_Reg
−0.9%
1.783
−1.4%
1.774
−1.5%
1.773
1.8
1.8
1.8
2.9
0.04
+0.9%
1.817
+1.4%
1.826
+1.5%
1.827
V
V
V
V
mV/V
Load_Reg
0.04
mV/mA
V_DO
mV
620
230
95
I_pk
500
700
830
mA
I_sc
900
mA
T_J
160/10
C
I_GND
9.0
14
mA
4.6
7.5
0.8
2.5
−
220
mA
In Dropout
V_in = 2.2 V, I_load = 0.1 mA
500
mA
In Shutdown
V_SD = 0 V
Output Noise
C_nr = 0 nF, I_load = 500 mA, f = 10 Hz to 100 kHz, C_out = 10 mF
C_nr = 10 nF, I_load = 500 mA, f = 10 Hz to 100 kHz, C_out = 10 mF
Power Good Voltage
Low Threshold
Hysteresis
High Threshold
I_GNDsh
V_noise
V_elft
93
1.0
mA
52
mVrms
33
mVrms
% of
95
V_out
2
97
99
Power Good Pin Voltage Saturation (I_ef − 1.0 mA)
Power Good Pin Leakage
Power Good Blanking Time (Note 7)
Shutdown
Threshold Voltage ON
Threshold Voltage OFF
V_efdo
200
mV
I_efleak
1.0
mA
t_ef
50
ms
V_SD
2.0
V
0.4
V
SD Input Current, V_SD = 0 V to 0.4 V or V_SD = 2.0 V to V_in
I_SD
0.07
1.0
mA
Output Current In Shutdown Mode, V_out = 0 V
I_OSD
0.07
1.0
mA
Reverse Bias Protection, Current Flowing from the Output Pin to GND
I_OUTR
10
mA
(V_in = 0 V, V_{out_forced} = 1.8 V)
2. Performance guaranteed over the operating temperature range by design and/or characterization, production tested at T_J = T_A = 25C. Low
duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible.
3. T_A must be greater than 0C.
4. Maximum dropout voltage is limited by minimum input voltage V_in = 2.9 V recommended for guaranteed operation.
http://onsemi.com
5