MC74VHC4066 Datasheet, PDF (5/13 Pages) Motorola, Inc – Quad Analog Switch/Multiplexer/Demultiplexer

ADDITIONAL APPLICATION CHARACTERISTICS (Voltages Referenced to GND Unless Noted)
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _Symbol
Parameter
V_CC
Test Conditions
V
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _{BW Maximum On−Channel Bandwidth or fin = 1 MHz Sine Wave}
4.5
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ Minimum Frequency Response
Adjust f_in Voltage to Obtain 0 dBm at V_OS
9.0
(Figure NO TAG)
Increase f_in Frequency Until dB Meter Reads
12.0
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _{– 3 dB}
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ^RL ^{= 50 Ω, C}L ^{= 10 pF}
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ^—
Off−Channel Feedthrough Isolation f_in  Sine Wave
4.5
(Figure NO TAG)
Adjust f_in Voltage to Obtain 0 dBm at V_IS
9.0
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _{fin = 10 kHz, RL = 600 Ω, CL = 50 pF 12.0}
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _{fin = 1.0 MHz, RL = 50 Ω, CL = 10 pF}
4.5
9.0
12.0
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _—
Feedthrough Noise, Control to
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _Switch
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ^{(Figure NO TAG)}
V_in v 1 MHz Square Wave (t_r = t_f = 6 ns)
4.5
Adjust R_L at Setup so that I_S = 0 A
9.0
R_L = 600 Ω, C_L = 50 pF 12.0
R_L = 10 kΩ, C_L = 10 pF 4.5
9.0
12.0
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _—
Crosstalk Between Any Two
Switches
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ^{(Figure 16)}
f_in  Sine Wave
Adjust f_in Voltage to Obtain 0 dBm at V_IS
f_in = 10 kHz, R_L = 600 Ω, C_L = 50 pF
f_in = 1.0 MHz, R_L = 50 Ω, C_L = 10 pF
4.5
9.0
12.0
4.5
9.0
12.0
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _THD
Total Harmonic Distortion
(Figure 20)
f_in = 1 kHz, R_L = 10 kΩ, C_L = 50 pF
THD = THD_Measured − THD_Source
V_IS = 4.0 V_PP sine wave
V_IS = 8.0 V_PP sine wave
V_IS = 11.0 V_PP sine wave
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _{*Guaranteed limits not tested. Determined by design and verified by qualification.}
4.5
9.0
12.0
Limit*
25_C
74HC
150
160
160
Unit
MHz
− 50
dB
− 50
− 50
− 40
− 40
− 40
60
mV_PP
130
200
30
65
100
– 70
dB
– 70
– 70
– 80
– 80
– 80
%
0.10
0.06
0.04
400
350
300
250
200
150
+25 _C
100
+125_C
50
−55_C
0
0.00 0.20 0.40 0.60 0.80 1.00 1.20 1.40 1.60 1.80 2.00
V_is, INPUT VOLTAGE (VOLTS), REFERENCED TO GROUND
Figure 2. Typical On Resistance, V_CC = 2.0 V
http://onsemi.com
5