MC74HCT4066A Datasheet, PDF (5/13 Pages) ON Semiconductor – Quad Analog Switch Multiplexer/Demultiplexer

MC74HCT4066A
ADDITIONAL APPLICATION CHARACTERISTICS (Voltages Referenced to GND Unless Noted)
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _Symbol
Parameter
V_CC
Test Conditions
V
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _{BW Maximum On−Channel Bandwidth or fin = 1 MHz Sine Wave}
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _{Minimum Frequency Response}
Adjust f_in Voltage to Obtain 0 dBm at V_OS
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ^{(Figure 7)}
Increase f_in Frequency Until dB Meter Reads – 3 dB
R_L = 50 W, C_L = 10 pF 4.5
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _−
Off−Channel Feedthrough Isolation f_in  Sine Wave
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _{(Figure 8)}
Adjust f_in Voltage to Obtain 0 dBm at V_IS
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ^fin ^{= 10 kHz, R}L ^{= 600 W, C}L ^{= 50 pF 4.5}
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ^fin ^{= 1.0 MHz, R}L ^{= 50 W, C}L ^{= 10 pF 4.5}
−
Feedthrough Noise, Control to
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _Switch
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _{(Figure 9)}
V_in v 1 MHz Square Wave (t_r = t_f = 6 ns)
Adjust R_L at Setup so that I_S = 0 A
R_L = 600 W, C_L = 50 pF 4.5
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _{RL=10kW,CL=10pF 4.5}
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _−
Crosstalk Between Any Two
Switches
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _{(Figure 14)}
f_in  Sine Wave
Adjust f_in Voltage to Obtain 0 dBm at V_IS
f_in = 10 kHz, R_L = 600 W, C_L = 50 pF 4.5
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _{fin = 1.0 MHz, RL = 50 W, CL = 10 pF 4.5}
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _THD
Total Harmonic Distortion
(Figure 16)
f_in = 1 kHz, R_L = 10 kW, C_L = 50 pF
THD = THD_Measured − THD_Source
V_IS = 4.0 V_PP sine wave 4.5
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _{*Guaranteed limits not tested. Determined by design and verified by qualification.}
Limit*
25°C
54/74HCT
Unit
MHz
150
dB
−50
−40
mV_PP
60
30
dB
–70
–80
%
0.10
http://onsemi.com
5