MC74HC4316A_11 Datasheet, PDF (5/11 Pages) ON Semiconductor – Quad Analog Switch/Multiplexer/Demultiplexer with Separate Analog and Digital Power Supplies

MC74HC4316A
AC ELECTRICAL CHARACTERISTICS (C_L = 50 pF, Control or Enable t_r = t_f = 6 ns, V_EE = GND)
Guaranteed Limit
Symbol
Parameter
t_PLH,
t_PHL
Maximum Propagation Delay, Analog Input to Analog Output
(Figures 9 and 10)
t_PLZ,
t_PHZ
Maximum Propagation Delay, Control or Enable to Analog Output
(Figures 11 and 12)
t_PZL,
t_PZH
Maximum Propagation Delay, Control or Enable to Analog Output
(Figures 11 and 12)
C
Maximum Capacitance
ON/OFF Control
and Enable Inputs
Control Input = GND
Analog I/O
Feedthrough
V_CC – 55 to
V
25°C v 85°C v 125°C _Unit
2.0
40
50
60
ns
4.5
6
8
9
6.0
5
7
8
2.0
130
160
200
ns
4.5
40
50
60
6.0
30
40
50
2.0
140
175
250
ns
4.5
40
50
60
6.0
30
40
50
−
10
10
10
pF
−
35
35
35
−
1.0
1.0
1.0
Typical @ 25°C, V_CC = 5.0 V
C_PD Power Dissipation Capacitance (Per Switch) (Figure 14)*
15
pF
*Used to determine the no−load dynamic power consumption: P_D = C_PD V_CC2f + I_CC V_CC.
ADDITIONAL APPLICATION CHARACTERISTICS (GND = 0 V)
Symbol
Parameter
V_CC
Test Conditions
V
BW Maximum On–Channel Bandwidth f_in = 1 MHz Sine Wave
2.25
or
Adjust f_in Voltage to Obtain 0 dBm at V_OS
4.50
Minimum Frequency Response
Increase f_in Frequency Until dB Meter
6.00
(Figure 6)
Reads – 3 dB
R_L = 50 W, C_L = 10 pF
−
Off–Channel Feedthrough
Isolation
(Figure 7)
f_in  Sine Wave
Adjust f_in Voltage to Obtain 0 dBm at V_IS
f_in = 10 kHz, R_L = 600 W, C_L = 50 pF
2.25
4.50
6.00
f_in = 1.0 MHz, R_L = 50 W, C_L = 10 pF
2.25
4.50
6.00
−
Feedthrough Noise, Control to
Switch
(Figure 8)
V_in v 1 MHz Square Wave (t_r = t_f = 6 ns)
2.25
Adjust R_L at Setup so that I_S = 0 A
4.50
R_L = 600 W, C_L = 50 pF 6.00
R_L = 10 kW, C_L = 10 pF 2.25
4.50
6.00
−
Crosstalk Between Any Two
Switches
(Figure 13)
f_in  Sine Wave
Adjust f_in Voltage to Obtain 0 dBm at V_IS
f_in = 10 kHz, R_L = 600 W, C_L = 50 pF
f_in = 1.0 MHz, R_L = 50 W, C_L = 10 pF
2.25
4.50
6.00
2.25
4.50
6.00
THD
Total Harmonic Distortion
(Figure 15)
f_in = 1 kHz, R_L = 10 kW, C_L = 50 pF
THD = THD_Measured − THD_Source
V_IS = 4.0 V_PP sine wave
V_IS = 8.0 V_PP sine wave
V_IS = 11.0 V_PP sine wave
*Limits not tested. Determined by design and verified by qualification.
2.25
4.50
6.00
V_EE
V
– 2.25
– 4.50
– 6.00
– 2.25
– 4.50
– 6.00
– 2.25
– 4.50
– 6.00
– 2.25
– 4.50
– 6.00
– 2.25
– 4.50
– 6.00
– 2.25
– 4.50
– 6.00
– 2.25
– 4.50
– 6.00
– 2.25
– 4.50
– 6.00
Limit*
25°C
150
160
160
Unit
MHz
– 50
dB
– 50
– 50
– 40
– 40
– 40
30
mV_PP
65
100
60
130
200
– 70
dB
– 70
– 70
– 80
– 80
– 80
%
0.10
0.06
0.04
http://onsemi.com
5