CM2020-01TR_11 Datasheet, PDF (5/9 Pages) ON Semiconductor – HDMI Transmitter Port Protection and Interface Device

CM2020−01TR
SPECIFICATIONS (Cont’d)
Table 4. ELECTRICAL OPERATING CHARACTERISTICS (Note 1)
Symbol
Parameter
Conditions
Min Typ Max Units
I_CC5V
I_CCLV
V_DROP
I_SC
Operating Supply Current
Bias Supply Current
5V_OUT Overcurrent Output Drop
5V_OUT Short Circuit Current Limit
5V_SUPPLY = 5.0 V
LV_SUPPLY = 3.3 V
5V_SUPPLY = 5.0 V,
I_OUT = 55 mA
5V_SUPPLY = 5.0 V,
5V_OUT = GND
110 130 mA
1
5
mA
65 100 mV
90 135 175 mA
I_OFF
OFF State Leakage Current, Level Shifting
LV_SUPPLY = 0 V
NFET
0.1 5.0 mA
I_BACKDRIVE Current Conducted from Output Pins to
V_SUPPLY Rails when Powered Down
5V_SUPPLY < V_{CH_OUT}
Signal Pins: TMDS_D[2:0]+/−,
TMDS_CK+/−, CE_REMOTE_OUT,
DDC_DAT_OUT, DDC_CLK_OUT,
HOTPLUG_DET_OUT, 5V_OUT
Only
0.1 5.0 mA
I_BACKDRIVE, Current through CE−REMOTE_OUT when
CEC
Powered Down
CE−REMOTE_IN = CE_SUPPLY <
CE_REMOTE_OUT
0.1 1.0 mA
V_ON
VOLTAGE Drop Across Level Shifting NFET LV_SUPPLY = 2.5 V, V_S = GND,
when ON
I_DS = 3 mA
75
95 140 mV
V_F
Diode Forward Voltage
Top Diode
Bottom Diode
I_F = 8 mA, T_A = 25°C
V
0.60 0.85 0.95
0.60 0.85 0.95
V_ESD
ESD Withstand Voltage
Pins 4, 7, 10, 13, 20, 21, 22, 23, 24,
kV
Contact Discharge per
27, 30, 33, 38
±8
IEC 61000−4−2 Standard
(Note 2)
V_CL
Channel Clamp Voltage
Positive Transients
Negative Transients
T_A = 25°C, I_PP = 1 A, t_P = 8/20 ms
(Note 3)
V
11.0
−2.0
R_DYN
Dynamic Resistance
Positive Transients
Negative Transients
T_A = 25°C, I_PP = 1 A, t_P = 8/20 ms
(Note 3)
W
1.2
0.9
I_LEAK
TMDS Channel Leakage Current
T_A = 25°C
0.01 1
mA
C_IN, TMDS TMDS Channel Input Capacitance
5V_SUPPLY = 5.0 V, Measured at
1 MHz, V_BIAS = 2.5 V
0.9 1.2 pF
DC_IN, TMDS TMDS Channel Input Capacitance Matching
5V_SUPPLY = 5.0 V, Measured at
1 MHz, V_BIAS = 2.5 V (Note 4)
0.05
pF
C_IN, DDC
Level Shifting Input Capacitance, Capacitance 5V_SUPPLY = 5 V, Measured at
to GND
100 kHz, V_BIAS = 2.5 V
3.5
4
pF
C_IN, CEC
Level Shifting Input Capacitance, Capacitance 5V_SUPPLY = 5 V, Measured at
to GND
100 kHz, V_BIAS = 2.5 V
3.5
4
pF
C_IN, HP
Level Shifting Input Capacitance, Capacitance 5V_SUPPLY = 5 V, Measured at
to GND
100 kHz, V_BIAS = 2.5 V
3.5
4
pF
1. Operating Characteristics are over Standard Operating Conditions unless otherwise specified.
2. Standard IEC 61000−4−2, C_DISCHARGE = 150 pF, R_DISCHARGE = 330 W, 5V_SUPPLY and LV_SUPPLY within recommended operating
conditions, GND = 0 V, 5V_OUT (pin 38), each bypassed with a 0.1 mF ceramic capacitor connected to GND.
3. These measurements performed with no external capacitor on ESD_BYP.
4. Intra−pair matching, each TMDS pair (i.e. D+, D−).
http://onsemi.com
5