MC74LCX540_12 Datasheet, PDF (4/8 Pages) ON Semiconductor – Low-Voltage CMOS Octal Buffer Flow Through Pinout

MC74LCX540
DC ELECTRICAL CHARACTERISTICS
Symbol
Characteristic
Condition
V_IH HIGH Level Input Voltage (Note 2)
V_IL LOW Level Input Voltage (Note 2)
V_OH HIGH Level Output Voltage
V_OL LOW Level Output Voltage
2.7 V ≤ V_CC ≤ 3.6 V
2.7 V ≤ V_CC ≤ 3.6 V
2.7 V ≤ V_CC ≤ 3.6 V; I_OH = −100 mA
V_CC = 2.7 V; I_OH = −12 mA
V_CC = 3.0 V; I_OH = −18 mA
V_CC = 3.0 V; I_OH = −24 mA
2.7 V ≤ V_CC ≤ 3.6 V; I_OL = 100 mA
V_CC = 2.7 V; I_OL = 12 mA
V_CC = 3.0 V; I_OL = 16 mA
V_CC = 3.0 V; I_OL = 24 mA
I_OZ 3−State Output Current
V_CC = 3.6 V, V_IN = V_IH or V_IL,
V_OUT = 0 to 3.6 V
I_OFF Power Off Leakage Current
V_CC = 0, V_IN = 3.6 V or V_OUT = 3.6 V
I_IN
Input Leakage Current
V_CC = 0 to 3.6 V, V_IN = 3.6 V or GND
I_CC Quiescent Supply Current
V_CC = 3.6 V, V_IN = 3.6 V or V_OUT = 3.6 V
DI_CC Increase in I_CC per Input
2.3 ≤ V_CC ≤ 3.6 V; V_IH = V_CC − 0.6 V
2. These values of V_I are used to test DC electrical characteristics only.
T_A = −40°C to +85°C
Min
Max
2.0
0.8
V_CC − 0.2
2.2
2.4
2.2
0.2
0.4
0.4
0.55
±5
10
±5
10
500
Units
V
V
V
V
mA
mA
mA
mA
mA
AC CHARACTERISTICS (t_R = t_F = 2.5 ns; C_L = 50 pF; R_L = 500 W)
Limits
Symbol
Parameter
Waveform
T_A = −40°C to +85°C
V_CC = 3.0 V to 3.6 V
V_CC = 2.7 V
Min
Max
Max
Units
t_PLH Propagation Delay
t_PHL Input to Output
1
1.5
6.5
7.5
ns
1.5
6.5
7.5
t_PZH Output Enable Time to
t_PZL High and Low Level
2
1.5
8.5
9.5
ns
1.5
8.5
9.5
t_PHZ Output Disable Time From
t_PLZ High and Low Level
2
1.5
7.5
8.5
ns
1.5
7.5
8.5
t_OSHL
t_OSLH
Output−to−Output Skew (Note 3)
1.0
ns
1.0
3. Skew is defined as the absolute value of the difference between the actual propagation delay for any two separate outputs of the same device.
The specification applies to any outputs switching in the same direction, either HIGH−to−LOW (t_OSHL) or LOW−to−HIGH (t_OSLH); parameter
guaranteed by design.
DYNAMIC SWITCHING CHARACTERISTICS
Symbol
Characteristic
Condition
T_A = +25°C
Min Typ Max
Units
V_OLP Dynamic LOW Peak Voltage (Note 4)
V_CC = 3.3 V, C_L = 50 pF, V_IH = 3.3 V, V_IL = 0 V
0.8
V
V_OLV Dynamic LOW Valley Voltage (Note 4) V_CC = 3.3 V, C_L = 50 pF, V_IH = 3.3 V, V_IL = 0 V
0.8
V
4. Number of outputs defined as “n”. Measured with “n−1” outputs switching from HIGH−to−LOW or LOW−to−HIGH. The remaining output is
measured in the LOW state.
CAPACITIVE CHARACTERISTICS
Symbol
Parameter
C_IN
C_OUT
C_PD
Input Capacitance
Output Capacitance
Power Dissipation Capacitance
Condition
V_CC = 3.3 V, V_I = 0 V or V_CC
V_CC = 3.3 V, V_I = 0 V or V_CC
10 MHz, V_CC = 3.3V, V_I = 0 V or V_CC
Typical
7
8
25
Units
pF
pF
pF
http://onsemi.com
4