English
Language : 

TCA0372_05 Datasheet, PDF (3/10 Pages) ON Semiconductor – 1.0 A Output Current, Dual Power Operational Amplifiers
◁
TCA0372, TCA0372B
DC ELECTRICAL CHARACTERISTICS (VCC = +15 V, VEE = −15 V, RL connected to ground, TA = −40° to +125°C.)
Characteristics
Symbol
Min
Typ
Max
Input Offset Voltage (VCM = 0)
TA = +25°C
TA, Tlow to Thigh
Average Temperature Coefficient of Offset Voltage
Input Bias Current (VCM = 0)
Input Offset Current (VCM = 0)
Large Signal Voltage Gain
VO = ±10 V, RL = 2.0 k
Output Voltage Swing (IL = 100 mA)
TA = +25°C
TA = Tlow to Thigh
TA = +25°C
TA = Tlow to Thigh
Output Voltage Swing (IL = 1.0 A)
VCC = +24 V, VEE = 0 V, TA = +25°C
VCC = +24 V, VEE = 0 V, TA = Tlow to Thigh
VCC = +24 V, VEE = 0 V, TA = +25°C
VCC = +24 V, VEE = 0 V, TA = Tlow to Thigh
Input Common Mode Voltage Range
TA = +25°C
TA = Tlow to Thigh
Common Mode Rejection Ratio (RS = 10 k)
Power Supply Rejection Ratio (RS = 100 W)
Power Supply Current
TA = +25°C
TA = Tlow to Thigh
TCA0372
TCA0372B
TCA0372
TCA0372B
VIO
DVIO/DT
IIB
IIO
AVOL
VOH
VOL
VOH
VOL
VICR
CMRR
PSRR
ID
−
1.0
15
−
−
20
−
20
−
−
100
500
−
10
50
30
100
−
14.0 14.2
−
13.9
−
−
−
−14.2 −14.0
−
−
−13.9
22.5 22.7
−
22.5
−
−
−
1.3
1.5
−
−
1.5
VEE to (VCC −1.0)
VEE to (VCC −1.3)
70
90
−
70
90
−
−
5.0
10
−
8.0
10
−
−
14
−
−
14
Unit
mV
mV/°C
nA
nA
V/mV
V
V
V
dB
dB
mA
AC ELECTRICAL CHARACTERISTICS (VCC = +15 V, VEE = −15 V, RL connected to ground, TA = +25°C, unless otherwise noted.)
Characteristics
Symbol
Min
Typ
Max
Unit
Slew Rate (Vin = −10 V to +10 V, RL = 2.0 k, CL = 100 pF)
AV = −1.0, TA = Tlow to Thigh
SR
1.0
1.4
−
V/ms
Gain Bandwidth Product (f = 100 kHz, CL = 100 pF, RL = 2.0 k)
TA = 25°C
TA = Tlow to Thigh
GBW
0.9
1.4
−
0.7
−
−
MHz
Phase Margin TJ = Tlow to Thigh
RL = 2.0 k, CL = 100 pF
fm
−
65
−
Degrees
Gain Margin
RL = 2.0 k, CL = 100 pF
Am
−
15
−
dB
Equivalent Input Noise Voltage
RS = 100 W, f = 1.0 to 100 kHz
en
−
22
−
nV/√ Hz
Total Harmonic Distortion
AV = −1.0, RL = 50 W, VO = 0.5 VRMS, f = 1.0 kHz
THD
−
0.02
−
%
NOTE: In case VEE is disconnected before VCC, a diode between VEE and Ground is recommended to avoid damaging the device.
http://onsemi.com
3
 ▷