MLP1N06CL Datasheet, PDF (3/8 Pages) Motorola, Inc – VOLTAGE CLAMPED CURRENT LIMITING MOSFET

MLP1N06CL
4
TJ = 25°C
4 ^{VDS ≥ 7.5 V}
3
10 V
6V
8V
3
4V
2
2
-50°C
25°C
1
VGS = 3 V
1
TJ = 150°C
0
0
2
4
6
8
VDS, DRAIN-TO-SOURCE VOLTAGE (VOLTS)
Figure 1. Output Characteristics
THE SMARTDISCRETES CONCEPT
From a standard power MOSFET process, several active
and passive elements can be obtained that provide on–chip
protection to the basic power device. Such elements require
only a small increase in silicon area and/or the addition of one
masking layer to the process. The resulting device exhibits
significant improvements in ruggedness and reliability as
well as system cost reduction. The SMARTDISCRETES
device functions can now provide an economical alternative
to smart power ICs for power applications requiring low
on–resistance, high voltage and high current.
These devices are designed for applications that require a
rugged power switching device with short circuit protection
that can be directly interfaced to a microcontroller unit
(MCU). Ideal applications include automotive fuel injector
driver, incandescent lamp driver or other applications where
a high in–rush current or a shorted load condition could occur.
OPERATION IN THE CURRENT LIMIT MODE
The amount of time that an unprotected device can
withstand the current stress resulting from a shorted load
before its maximum junction temperature is exceeded is
dependent upon a number of factors that include the amount
of heatsinking that is provided, the size or rating of the
device, its initial junction temperature, and the supply
voltage. Without some form of current limiting, a shorted
load can raise a device’s junction temperature beyond the
maximum rated operating temperature in only a few
milliseconds.
Even with no heatsink, the MLP1N06CL can withstand a
shorted load powered by an automotive battery (10 to 14
Volts) for almost a second if its initial operating temperature
is under 100°C. For longer periods of operation in the
current–limited mode, device heatsinking can extend
operation from several seconds to indefinitely depending on
the amount of heatsinking provided.
0
0
2
4
6
8
VGS, GATE-TO-SOURCE VOLTAGE (VOLTS)
Figure 2. Transfer Function
SHORT CIRCUIT PROTECTION AND THE EFFECT OF
TEMPERATURE
The on–chip circuitry of the MLP1N06CL offers an
integrated means of protecting the MOSFET component
from high in–rush current or a shorted load. As shown in the
schematic diagram, the current limiting feature is provided
by an NPN transistor and integral resistors R1 and R2. R2
senses the current through the MOSFET and forward biases
the NPN transistor’s base as the current increases. As the
NPN turns on, it begins to pull gate drive current through R1,
dropping the gate drive voltage across it, and thus lowering
the voltage across the gate–to–source of the power
MOSFET and limiting the current. The current limit is
temperature dependent as shown in Figure 3, and decreases
from about 2.3 Amps at 25°C to about 1.3 Amps at 150°C.
Since the MLP1N06CL continues to conduct current and
dissipate power during a shorted load condition, it is
important to provide sufficient heatsinking to limit the
device junction temperature to a maximum of 150°C.
The metal current sense resistor R2 adds about 0.4 ohms
to the power MOSFET’s on–resistance, but the effect of
temperature on the combination is less than on a standard
MOSFET due to the lower temperature coefficient of R2.
The on–resistance variation with temperature for gate
voltages of 4 and 5 Volts is shown in Figure 5.
Back–to–back polysilicon diodes between gate and
source provide ESD protection to greater than 2 kV, HBM.
This on–chip protection feature eliminates the need for an
external Zener diode for systems with potentially heavy line
transients.
http://onsemi.com
3