MC74LVXT4066_11 Datasheet, PDF (3/13 Pages) ON Semiconductor – Quad Analog Switch/Multiplexer/Demultiplexer

MC74LVXT4066
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ MAXIMUM RATINGS
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ Symbol
Parameter
Value
Unit
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ V_CC Positive DC Supply Voltage (Referenced to GND)
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ V_IS Analog Input Voltage (Referenced to GND)
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ V_in Digital Input Voltage (Referenced to GND)
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ I
DC Current Into or Out of Any Pin
– 0.5 to + 7.0
V
– 0.5 to V_CC + 0.5 V
– 0.5 to V_CC + 0.5 V
−20
mA
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ P_D Power Dissipation in Still Air,
SOIC Package†
500
mW
TSSOP Package†
450
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _{Tstg Storage Temperature}
– 65 to + 150
_C
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _{TL Lead Temperature, 1 mm from Case for 10 Seconds}
260
_C
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _{Maximum ratings are those values beyond which device damage can occur. Maximum ratings}
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _{applied to the device are individual stress limit values (not normal operating conditions) and are}
not valid simultaneously. If these limits are exceeded, device functional operation is not implied,
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _{damage may occur and reliability may be affected.}
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _{†Derating − SOIC Package: – 7 mW/_C from 65_ to 125_C}
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ^{TSSOP Package: − 6.1 mW/_C from 65_ to 125_C}
RECOMMENDED OPERATING CONDITIONS
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _Symbol
Parameter
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _{VCC Positive DC Supply Voltage (Referenced to GND)}
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _{VIS Analog Input Voltage (Referenced to GND)}
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _{Vin Digital Input Voltage (Referenced to GND)}
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _{VIO* Static or Dynamic Voltage Across Switch}
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _{TA Operating Temperature, All Package Types}
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _{tr, tf Input Rise and Fall Time, ON/OFF Control}
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ^{Inputs (Figure 10)}
V_CC = 3.3 V ± 0.3 V
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ^{VCC = 5.0 V ± 0.5 V}
Min
2.0
GND
GND
−
– 55
0
0
Max
5.5
V_CC
V_CC
1.2
+ 85
100
20
Unit
V
V
V
V
_C
ns/V
*For voltage drops across the switch greater than 1.2 V (switch on), excessive V_CC current may
be drawn; i.e., the current out of the switch may contain both V_CC and switch input components.
The reliability of the device will be unaffected unless the Maximum Ratings are exceeded.
This device contains protection
circuitry to guard against damage
due to high static voltages or electric
fields. However, precautions must
be taken to avoid applications of any
voltage higher than maximum rated
voltages to this high−impedance cir-
cuit. For proper operation, V_in and
V_out should be constrained to the
range GND v (V_in or V_out) v V_CC.
Unused inputs must always be
tied to an appropriate logic voltage
level (e.g., either GND or V_CC).
Unused outputs must be left open.
I/O pins must be connected to a
properly terminated line or bus.
DC ELECTRICAL CHARACTERISTIC Digital Section (Voltages Referenced to GND)
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _Symbol
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _VIH
Parameter
Minimum High−Level Voltage
ON/OFF Control Inputs
(Note 1)
Test Conditions
R_on = Per Spec
V_CC
Guaranteed Limit
V
– 55 to 25_C v 85_C v 125_C Unit
3.0
1.2
4.5
2.0
5.5
2.0
1.2
1.2
V
2.0
2.0
2.0
2.0
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _{VIL Maximum Low−Level Voltage}
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _{ON/OFF Control Inputs}
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ (Note 1)
R_on = Per Spec
3.0
0.53
0.53
0.53
V
4.5
0.8
0.8
0.8
5.5
0.8
0.8
0.8
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ^Iin
Maximum Input Leakage Current V_in = V_CC or GND
ON/OFF Control Inputs
5.5
± 0.1
± 1.0
± 1.0
mA
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _{ICC Maximum Quiescent Supply}
V_in = V_CC or GND V_IO = 0 V
5.5
4.0
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _{Current (per Package)}
40
160
mA
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ 1. Specifications are for design target only. Not final specification limits.
http://onsemi.com
3