|
MC74LVX4066_11 Datasheet, PDF (3/13 Pages) ON Semiconductor – Quad Analog Switch/Multiplexer/Demultiplexer | |||
|
◁ |
MC74LVX4066
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃ MAXIMUM RATINGS
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃ Symbol
Parameter
Value
Unit
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃ VCC Positive DC Supply Voltage (Referenced to GND)
â 0.5 to + 7.0
V
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃ VIS Analog Input Voltage (Referenced to GND)
â 0.5 to VCC + 0.5 V
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃ Vin Digital Input Voltage (Referenced to GND)
â 0.5 to VCC + 0.5 V
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃ Iin
DC Current Into or Out of ON/OFF Control Pins
± 20
mA
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃ Is
DC Current Into or Out of Switch Pins
± 20
mA
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃ PD Power Dissipation in Still Air,
SOIC Packageâ
500
mW
TSSOP Packageâ
450
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃ Tstg Storage Temperature
â 65 to + 150
_C
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃ TL Lead Temperature, 1 mm from Case for 10 Seconds
260
_C
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃ Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃ ratings only. Functional operation above the Recommended Operating Conditions is not im-
plied. Extended exposure to stresses above the Recommended Operating Conditions may af-
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃ fect device reliability.
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃ â Derating â SOIC Package: â 7 mW/_C from 65_ to 125_C
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃ TSSOP Package: â 6.1 mW/_C from 65_ to 125_C
RECOMMENDED OPERATING CONDITIONS
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃ Symbol
Parameter
Min
Max Unit
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃ VCC Positive DC Supply Voltage (Referenced to GND)
2.0
6.0
V
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃ VIS Analog Input Voltage (Referenced to GND)
GND
VCC
V
Vin Digital Input Voltage (Referenced to GND)
GND
VCC
V
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃ VIO* Static or Dynamic Voltage Across Switch
â
1.2
V
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃ TA Operating Temperature, All Package Types
â 55
+ 85 _C
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃ tr, tf Input Rise and Fall Time, ON/OFF Control
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃ Inputs (Figure 10)
VCC = 3.3 V ± 0.3 V
0
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃà VCC = 5.0 V ± 0.5 V
0
ns/V
100
20
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃ *For voltage drops across the switch greater than 1.2 V (switch on), excessive VCC current may
be drawn; i.e., the current out of the switch may contain both VCC and switch input
components. The reliability of the device will be unaffected unless the Maximum Ratings are
exceeded.
This device contains protection
circuitry to guard against damage
due to high static voltages or electric
fields. However, precautions must
be taken to avoid applications of any
voltage higher than maximum rated
voltages to this highâimpedance cir-
cuit. For proper operation, Vin and
Vout should be constrained to the
range GND v (Vin or Vout) v VCC.
Unused inputs must always be
tied to an appropriate logic voltage
level (e.g., either GND or VCC).
Unused outputs must be left open.
I/O pins must be connected to a
properly terminated line or bus.
DC ELECTRICAL CHARACTERISTIC Digital Section (Voltages Referenced to GND)
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃ Symbol
Parameter
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃ VIH Minimum HighâLevel Voltage
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃ ON/OFF Control Inputs (Note 1)
Test Conditions
Ron = Per Spec
VCC
Guaranteed Limit
V â 55 to 25_C v 85_C v 125_C Unit
2.0
1.5
3.0
2.1
4.5
3.15
5.5
3.85
1.5
1.5
V
2.1
2.1
3.15
3.15
3.85
3.85
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃ VIL Maximum LowâLevel Voltage
Ron = Per Spec
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃ ON/OFF Control Inputs (Note 1)
2.0
0.5
3.0
0.9
4.5
1.35
5.5
1.65
0.5
0.5
V
0.9
0.9
1.35
1.35
1.65
1.65
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃ Iin
Maximum Input Leakage Current Vin = VCC or GND
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃ ON/OFF Control Inputs
5.5V
± 0.1
± 1.0
± 1.0
mA
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃ ICC Maximum Quiescent Supply
Vin = VCC or GND VIO = 0 V
5.5
4.0
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃ Current (per Package)
ÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃÃ 1. Specifications are for design target only. Not final specification limits.
40
160
mA
http://onsemi.com
3
|
▷ |