MC74LCX06 Datasheet, PDF (3/6 Pages) ON Semiconductor – Low-Voltage CMOS Hex Inverter with Open Drain Outputs

MC74LCX06
RECOMMENDED OPERATING CONDITIONS
Symbol
Parameter
V_CC
Supply Voltage
Operating
Data Retention Only
V_I
V_O
I_OL
T_A
Dt/DV
Input Voltage
Output Voltage
(HIGH or LOW State)
LOW Level Output Current
Sink
Operating Free−Air Temperature
V_CC = 3.0 V − 3.6 V
V_CC = 2.7 V − 3.0 V
V_CC = 2.3 V − 2.7 V
Input Transition Rise or Fall Rate, V_IN from 0.8 V to 2.0 V, V_CC = 3.0 V
Min
Typ
Max
Unit
2.0
2.5, 3.3
3.6
V
1.5
2.5, 3.3
3.6
0
5.5
V
0
V_CC
V
+24
mA
+12
+8
−40
+85
°C
0
10
ns/V
DC ELECTRICAL CHARACTERISTICS (T_A = −40°C to +85°C)
Symbol
Characteristic
Condition
V_IH
HIGH Level Input Voltage (Note 2)
2.3 V ≤ V_CC ≤ 2.7 V
2.7 V ≤ V_CC ≤ 3.6 V
V_IL
LOW Level Input Voltage (Note 2)
2.3 V ≤ V_CC ≤ 2.7 V
2.7 V ≤ V_CC ≤ 3.6 V
V_OL
LOW Level Output Voltage
2.3 V ≤ V_CC ≤ 3.6 V; I_OL = 100 mA
V_CC = 2.3 V; I_OL= 8 mA
V_CC = 2.7 V; I_OL= 12 mA
V_CC = 3.0 V; I_OL = 16 mA
V_CC = 3.0 V; I_OL = 24 mA
I_I
Input Leakage Current
2.3 V ≤ V_CC ≤ 3.6 V; 0 V ≤ V_I ≤ 5.5 V
I_OFF
Power−Off Leakage Current
V_CC = 0 V; V_I or V_O = 5.5 V
I_CC
Quiescent Supply Current
2.3 V ≤ V_CC ≤ 3.6 V; V_I = GND or V_CC
2.3 V ≤ V_CC ≤ 3.6 V; 3.6 ≤ V_I ≤ 5.5 V
DI_CC
Increase in I_CC per Input
2.3 V ≤ V_CC ≤ 3.6 V
One Input at V_IH = V_CC − 0.6 V
2. These values of V_I are used to test DC electrical characteristics only.
AC ELECTRICAL CHARACTERISTICS (T_A = −40°C to +85°C)
V_CC = 3.3 V ± 0.3 V
C_L = 50 pF
V_CC= 2.7 V
C_L = 50 pF
Symbol
Parameter
Min
Max
Min
Max
t_PLZ
Propagation Delay
t_PZL
Input to Output
0.8
3.7
1.0
4.1
0.8
3.7
1.0
4.1
Min
Max
Unit
1.7
V
2.0
0.7
V
0.8
0.2
V
0.3
0.4
0.4
0.55
±5.0
mA
10
mA
10
mA
±10
mA
500
mA
V_CC = 2.5 V ± 0.2 V
C_L = 30 pF
Min
Max
Unit
0.8
3.5
ns
0.8
3.5
ns
DYNAMIC SWITCHING CHARACTERISTICS (T_A = +25°C)
Symbol
Characteristic
Condition
Min Typ Max Unit
V_OLP
Dynamic LOW Peak Voltage (Note 3)
V_CC = 3.3 V, C_L = 50 pF, V_IH = 3.3 V, V_IL = 0 V
0.9
V
V_CC = 2.5 V, C_L = 30 pF, V_IH = 2.5 V, V_IL = 0 V
0.7
V_OLV
Dynamic LOW Valley Voltage (Note 3) V_CC = 3.3 V, C_L = 50 pF, V_IH = 3.3 V, V_IL = 0 V
−0.8
V
V_CC = 2.5 V, C_L = 30 pF, V_IH = 2.5 V, V_IL = 0 V
−0.6
3. Number of outputs defined as “n”. Measured with “n−1” outputs switching from HIGH−to−LOW or LOW−to−HIGH. The remaining output is
measured in the LOW state.
CAPACITIVE CHARACTERISTICS
Symbol
Parameter
Condition
Typical
Unit
C_IN
C_OUT
C_PD
Input Capacitance
Output Capacitance
Power Dissipation Capacitance
V_CC = 3.3 V, V_I = 0 V or V_CC
7
pF
V_CC = 3.3 V, V_I = 0 V or V_CC
8
pF
10 MHz, V_CC = 3.3 V, V_I = 0 V or V_CC
25
pF
http://onsemi.com
3