MC74LCX04_14 Datasheet, PDF (3/7 Pages) ON Semiconductor – Low-Voltage CMOS Hex Inverter

MC74LCX04
DC ELECTRICAL CHARACTERISTICS
Symbol
Characteristic
Condition
V_IH
HIGH Level Input Voltage (Note 2)
2.3 V ≤ V_CC ≤ 2.7 V
2.7 V ≤ V_CC ≤ 3.6 V
V_IL
LOW Level Input Voltage (Note 2)
2.3 V ≤ V_CC ≤ 2.7 V
2.7 V ≤ V_CC ≤ 3.6 V
V_OH
HIGH Level Output Voltage
2.3 V ≤ V_CC ≤ 3.6 V; I_OH = −100 mA
V_CC = 2.3 V; I_OH = −8 mA
V_CC = 2.7 V; I_OH = −12 mA
V_CC = 3.0 V; I_OH = −18 mA
V_CC = 3.0 V; I_OH = −24 mA
V_OL
LOW Level Output Voltage
2.3 V ≤ V_CC ≤ 3.6 V; I_OL = 100 mA
V_CC = 2.3 V; I_OL = 8 mA
V_CC = 2.7 V; I_OL = 12 mA
V_CC = 3.0 V; I_OL = 16 mA
V_CC = 3.0 V; I_OL = 24 mA
I_OFF
Power Off Leakage Current
V_CC = 0, V_IN = 5.5 V or V_OUT = 5.5 V
I_IN
Input Leakage Current
V_CC = 3.6 V, V_IN = 5.5 V or GND
I_CC
Quiescent Supply Current
V_CC = 3.6 V, V_IN = 5.5 V or GND
DI_CC
Increase in I_CC per Input
2.3 ≤ V_CC ≤ 3.6 V; V_IH = V_CC − 0.6 V
2. These values of V_I are used to test DC electrical characteristics only.
T_A = −55°C to +125°C
Min
Max
Unit
1.7
V
2.0
0.7
V
0.8
V_CC − 0.2
V
1.8
2.2
2.4
2.2
0.2
V
0.6
0.4
0.4
0.55
10
mA
±5
mA
10
mA
500
mA
AC CHARACTERISTICS (t_R = t_F = 2.5 ns; R_L = 500 W)
Limits
Symbol
Parameter
Waveform
V_CC = 3.3 V ± 0.3 V
C_L = 50 pF
Min
Max
T_A = −55°C to +125°C
V_CC = 2.7 V
C_L = 50 pF
Min
Max
V_CC = 2.5 V ± 0.2 V
C_L = 30 pF
Min
Max
Unit
t_PLH
Propagation Delay Time
1
1.5
5.2
1.5
6.0
1.5
6.2
ns
t_PHL
Input to Output
1.5
5.2
1.5
6.0
1.5
6.2
t_OSHL
Output−to−Output Skew
1.0
ns
t_OSLH
(Note 3)
1.0
3. Skew is defined as the absolute value of the difference between the actual propagation delay for any two separate outputs of the same device.
The specification applies to any outputs switching in the same direction, either HIGH−to−LOW (t_OSHL) or LOW−to−HIGH (t_OSLH); parameter
guaranteed by design.
DYNAMIC SWITCHING CHARACTERISTICS
Symbol
Characteristic
Condition
T_A = +25°C
Min
Typ
Max Unit
V_OLP
Dynamic LOW Peak Voltage
V_CC = 3.3 V, C_L = 50 pF, V_IH = 3.3 V, V_IL = 0 V
0.8
V
(Note 4)
V_CC = 2.5 V, C_L = 30 pF, V_IH = 2.5 V, V_IL = 0 V
0.6
V
V_OLV
Dynamic LOW Valley Voltage
V_CC = 3.3 V, C_L = 50 pF, V_IH = 3.3 V, V_IL = 0 V
−0.8
V
(Note 4)
V_CC = 2.5 V, C_L = 30 pF, V_IH = 2.5 V, V_IL = 0 V
−0.6
V
4. Number of outputs defined as “n”. Measured with “n−1” outputs switching from HIGH−to−LOW or LOW−to−HIGH. The remaining output is
measured in the LOW state.
http://onsemi.com
3