MC74HC4060A_06 Datasheet, PDF (3/14 Pages) ON Semiconductor – 14−Stage Binary Ripple Counter With Oscillator

MC74HC4060A
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ MAXIMUM RATINGS
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ Symbol
Parameter
Value
Unit
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ V_CC DC Supply Voltage (Referenced to GND)
– 0.5 to + 7.0
V
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ V_in DC Input Voltage (Referenced to GND)
– 0.5 to V_CC + 0.5 V
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ V_out DC Output Voltage (Referenced to GND)
– 0.5 to V_CC + 0.5 V
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ I_in
DC Input Current, per Pin
± 20
mA
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ I_out DC Output Current, per Pin
± 25
mA
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ I_CC DC Supply Current, V_CC and GND Pins
± 50
mA
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ P_D Power Dissipation in Still Air,
Plastic DIP†
750
mW
SOIC Package†
500
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _{TSSOP Packageâ€} 
450
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _{Tstg Storage Temperature Range}
– 65 to + 150
_C
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _{TL Lead Temperature, 1 mm from Case for 10 Seconds}
_C
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ^{Plastic DIP, SOIC or TSSOP Package}
260
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ Maximum ratings are those values beyond which device damage can occur. Maximum ratings
This device contains protection
circuitry to guard against damage
due to high static voltages or electric
fields. However, precautions must
be taken to avoid applications of any
voltage higher than maximum rated
voltages to this high−impedance cir-
cuit. For proper operation, V_in and
V_out should be constrained to the
range GND v (V_in or V_out) v V_CC.
Unused inputs must always be
tied to an appropriate logic voltage
level (e.g., either GND or V_CC).
Unused outputs must be left open.
applied to the device are individual stress limit values (not normal operating conditions) and are
not valid simultaneously. If these limits are exceeded, device functional operation is not implied,
damage may occur and reliability may be affected.
†Derating — Plastic DIP: – 10 mW/_C from 65_ to 125_C
SOIC Package: – 7 mW/_C from 65_ to 125_C
TSSOP Package: − 6.1 mW/_C from 65_ to 125_C
For high frequency or heavy load considerations, see Chapter 2 of the ON Semiconductor High−Speed CMOS Data Book (DL129/D).
RECOMMENDED OPERATING CONDITIONS
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _Symbol
Parameter
Min
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _VCC
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _{Vin, Vout}
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _TA
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ^{tr, tf}
DC Supply Voltage (Referenced to GND)
DC Input Voltage, Output Voltage (Referenced to GND)
Operating Temperature Range, All Package Types
Input Rise/Fall Time
(Figure 1)
V_CC = 2.0 V
V_CC = 4.5 V
V_CC = 6.0 V
2.5*
0
– 55
0
0
0
Max Unit
6.0
V
V_CC
V
+ 125 _C
1000 ns
500
400
*The oscillator is guaranteed to function at 2.5 V minimum. However, parametrics are tested at
2.0 V by driving Pin 11 with an external clock source.
DC CHARACTERISTICS (Voltages Referenced to GND)
Symbol
Parameter
V_IH Minimum High−Level Input Voltage
Condition
V_out = 0.1V or V_CC −0.1V
|I_out| ≤ 20mA
V_CC
Guaranteed Limit
V −55 to 25°C ≤85°C ≤125°C Unit
2.0
1.50
1.50 1.50
V
3.0
2.10
2.10 2.10
4.5
3.15
3.15 3.15
6.0
4.20
4.20 4.20
V_IL Maximum Low−Level Input Voltage V_out = 0.1V or V_CC − 0.1V
|I_out| ≤ 20mA
2.0
0.50
0.50 0.50
V
3.0
0.90
0.90 0.90
4.5
1.35
1.35 1.35
6.0
1.80
1.80 1.80
V_OH Minimum High−Level Output Voltage V_in = V_IH or V_IL
(Q4−Q10, Q12−Q14)
|I_out| ≤ 20mA
2.0
1.9
4.5
4.4
6.0
5.9
1.9
1.9
V
4.4
4.4
5.9
5.9
V_in =V_IH or V_IL
|I_out| ≤ 2.4mA 3.0
|I_out| ≤ 4.0mA 4.5
|I_out| ≤ 5.2mA 6.0
2.48
3.98
5.48
2.34 2.20
3.84 3.70
5.34 5.20
http://onsemi.com
3