MC10EP51_06 Datasheet, PDF (3/11 Pages) ON Semiconductor – 3.3V / 5V ECL D Flip−Flop with Reset and Differential Clock

MC10EP51, MC100EP51
Table 4. MAXIMUM RATINGS
Symbol
Parameter
Condition 1
Condition 2
Rating
Unit
V_CC
PECL Mode Power Supply
V_EE
NECL Mode Power Supply
V_I
PECL Mode Input Voltage
NECL Mode Input Voltage
I_out
Output Current
V_EE = 0 V
V_CC = 0 V
V_EE = 0 V
V_CC = 0 V
Continuous
Surge
V_I v V_CC
V_I w V_EE
6
V
−6
V
6
V
−6
V
50
mA
100
mA
T_A
Operating Temperature Range
T_stg
Storage Temperature Range
q_JA
Thermal Resistance (Junction−to−Ambient) 0 lfpm
500 lfpm
SOIC−8
SOIC−8
−40 to +85
−65 to +150
190
130
°C
°C
°C/W
°C/W
q_JC
Thermal Resistance (Junction−to−Case)
Standard Board
q_JA
Thermal Resistance (Junction−to−Ambient) 0 lfpm
500 lfpm
SOIC−8
TSSOP−8
TSSOP−8
41 to 44
185
140
°C/W
°C/W
°C/W
q_JC
Thermal Resistance (Junction−to−Case)
Standard Board
q_JA
Thermal Resistance (Junction−to−Ambient) 0 lfpm
500 lfpm
TSSOP−8
DFN8
DFN8
41 to 44
129
84
°C/W
°C/W
°C/W
T_sol
Wave Solder
Pb
Pb−Free
265
°C
265
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
Table 5. 10EP DC CHARACTERISTICS, PECL V_CC = 3.3 V, V_EE = 0 V (Note 2)
−40°C
25°C
85°C
Symbol
Characteristic
Min Typ Max Min Typ Max Min Typ Max Unit
I_EE
Power Supply Current
26
34
44
26
35
45
28
37
47 mA
V_OH
Output HIGH Voltage (Note 3)
V_OL
Output LOW Voltage (Note 3)
2165 2290 2415 2230 2355 2480 2290 2415 2540 mV
1365 1490 1615 1430 1555 1680 1490 1615 1740 mV
V_IH
Input HIGH Voltage (Single−Ended)
V_IL
Input LOW Voltage (Single−Ended)
2090
1365
2415 2155
1690 1430
2480 2215
1755 1490
2540 mV
1815 mV
V_IHCMR Input HIGH Voltage Common Mode
2.0
Range (Differential Configuration) (Note 4)
3.3 2.0
3.3 2.0
3.3 V
I_IH
Input HIGH Current
I_IL
Input LOW Current
150
150
150 mA
0.5
0.5
0.5
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
2. Input and output parameters vary 1:1 with V_CC. V_EE can vary +0.3 V to −2.2 V.
3. All loading with 50 W to V_CC − 2.0 V.
4. V_IHCMR min varies 1:1 with V_EE, V_IHCMR max varies 1:1 with V_CC. The V_IHCMR range is referenced to the most positive side of the differential
input signal.
http://onsemi.com
3