MC10EP16VA_16 Datasheet, PDF (3/11 Pages) ON Semiconductor – ECL Differential Receiver/Driver

MC10EP16VA, MC100EP16VA
Table 3. MAXIMUM RATINGS
Symbol
Parameter
Condition 1
Condition 2
Rating
Unit
V_CC PECL Mode Power Supply
V_EE
NECL Mode Power Supply
V_I
PECL Mode Input Voltage
NECL Mode Input Voltage
I_out
Output Current
V_EE = 0 V
V_CC = 0 V
V_EE = 0 V
V_CC = 0 V
Continuous
Surge
V_I ≤ V_CC
V_I ≥ V_EE
6
V
−6
V
6
V
−6
50
mA
100
I_BB
V_BB Sink/Source
T_A
Operating Temperature Range
T_stg
Storage Temperature Range
q_JA
Thermal Resistance (Junction-to-Ambient) 0 lfpm
500 lfpm
SOIC−8 NB
SOIC−8 NB
±0.5
−40 to +85
−65 to +150
190
130
mA
°C
°C
°C/W
q_JC
Thermal Resistance (Junction-to-Case)
Standard Board
q_JA
Thermal Resistance (Junction-to-Ambient) 0 lfpm
500 lfpm
SOIC−8 NB
TSSOP−8
TSSOP−8
41 to 44
185
140
°C/W
°C/W
q_JC
Thermal Resistance (Junction-to-Case)
Standard Board
q_JA
Thermal Resistance (Junction-to-Ambient) 0 lfpm
500 lfpm
TSSOP−8
DFN8
DFN8
41 to 44
129
84
°C/W
°C/W
T_sol
Wave Solder (Pb-Free)
q_JC
Thermal Resistance (Junction-to-Case)
< 2 to 3 sec @ 260°C
(Note 2)
DFN8
265
35 to 40
°C
°C/W
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
2. JEDEC standard multilayer board − 2S2P (2 signal, 2 power)
Table 4. 10EP DC CHARACTERISTICS, PECL (V_CC = 3.3 V, V_EE = 0 V (Note 1))
−40°C
25°C
85°C
Symbol
Characteristic
Min Typ Max Min Typ Max Min Typ Max Unit
I_EE Power Supply Current
20
28
36
22
30
38
24
32
40 mA
V_OH Output HIGH Voltage (Note 2)
2165 2240 2415 2230 2355 2480 2290 2415 2540 mV
V_OL Output LOW Voltage (Note 2)
1365 1490 1615 1430 1555 1680 1490 1615 1740 mV
V_IH Input HIGH Voltage (Single-Ended)
2090
2415 2155
2480 2215
2540 mV
V_IL Input LOW Voltage (Single-Ended)
1365
1690 1460
1755 1490
1815 mV
V_BB Output Voltage Reference
1790 1950 1990 1855 2000 2055 1915 2040 2115 mV
V_IHCMR Input HIGH Voltage Common Mode
2.0
Range (Differential Configuration) (Note 3)
3.3 2.0
3.3 2.0
3.3 V
I_IH
Input HIGH Current
150
150
150 mA
I_IL
Input LOW Current
0.5
0.5
0.5
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
1. Input and output parameters vary 1:1 with V_CC. V_EE can vary +0.3 V to −2.2 V.
2. All loading with 50 W to V_CC − 2.0 V.
3. V_IHCMR min varies 1:1 with V_EE, V_IHCMR max varies 1:1 with V_CC. The V_IHCMR range is referenced to the most positive side of the differential
input signal.
www.onsemi.com
3