MC10EL58_06 Datasheet, PDF (3/9 Pages) ON Semiconductor – 5.0 V ECL 2:1 Multiplexer

MC10EL58, MC100EL58
Table 4. MAXIMUM RATINGS
Symbol
V_CC
V_EE
V_I
I_out
T_A
T_stg
q_JA
q_JC
q_JA
q_JC
q_JA
T_sol
Parameter
Condition 1
PECL Mode Power Supply
NECL Mode Power Supply
PECL Mode Input Voltage
NECL Mode Input Voltage
Output Current
V_EE = 0 V
V_CC = 0 V
V_EE = 0 V
V_CC = 0 V
Continuous
Surge
Operating Temperature Range
Storage Temperature Range
Thermal Resistance (Junction−to−Ambient)
0 lfpm
500 lfpm
Thermal Resistance (Junction−to−Case)
Thermal Resistance (Junction−to−Ambient)
0 lfpm
500 lfpm
Thermal Resistance (Junction−to−Case)
Standard Board
Thermal Resistance (Junction−to−Ambient)
0 lfpm
500 lfpm
Wave Solder
Pb <2 to 3 sec @ 248°C
Pb−Free <2 to 3 sec @ 260°C
Condition 2
V_I  V_CC
V_I  V_EE
SOIC−8
SOIC−8
SOIC−8
TSSOP−8
TSSOP−8
TSSOP−8
DFN8
DFN8
Rating
8
−8
6
−6
50
100
−40 to +85
−65 to +150
190
130
41 to 44
185
140
41 to 44
129
84
265
265
Unit
V
V
V
V
mA
mA
°C
°C
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
°C
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
Table 5. 10EL SERIES PECL DC CHARACTERISTICS V_CC= 5.0 V; V_EE= 0.0 V (Note 2)
−40°C
25°C
85°C
Symbol
Characteristic
Min Typ Max Min Typ Max Min Typ Max Unit
I_EE
Power Supply Current
V_OH
Output HIGH Voltage (Note 3)
V_OL
Output LOW Voltage (Note 3)
V_IH
Input HIGH Voltage
V_IL
Input LOW Voltage
I_IH
Input HIGH Current
I_IL
Input LOW Current
14
17
14
17
14
17 mA
3920 4010 4110 4020 4105 4190 4090 4185 4280 mV
3050 3200 3350 3050 3210 3370 3050 3227 3405 mV
3770
4110 3870
4190 3940
4280 mV
3050
3500 3050
3520 3050
3555 mV
150
150
150 mA
0.5
0.5
0.3
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
2. Input and output parameters vary 1:1 with V_CC. V_EE can vary +0.06 V / −0.5 V.
3. Outputs are terminated through a 50 ohm resistor to V_CC−2 volts.
http://onsemi.com
3