CAT24C512 Datasheet, PDF (3/15 Pages) ON Semiconductor – 512 kb I2C CMOS Serial EEPROM 128−Byte Page Write Buffer

CAT24C512
Table 1. ABSOLUTE MAXIMUM RATINGS
Parameters
Ratings
Units
Storage Temperature
–65 to +150
°C
Voltage on any Pin with Respect to Ground (Note 1)
–0.5 to +6.5
V
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
1. The DC input voltage on any pin should not be lower than −0.5 V or higher than V_CC + 0.5 V. During transitions, the voltage on any pin may
undershoot to no less than −1.5 V or overshoot to no more than V_CC + 1.5 V, for periods of less than 20 ns.
Table 2. RELIABILITY CHARACTERISTICS (Note 2)
Symbol
Parameter
Min
Units
N_END (Note 3)
Endurance
1,000,000
Program/Erase Cycles
T_DR
Data Retention
100
Years
2. These parameters are tested initially and after a design or process change that affects the parameter according to appropriate AEC−Q100
and JEDEC test methods.
3. Page Mode, V_CC = 5 V, 25°C.
Table 3. D.C. OPERATING CHARACTERISTICS
V_CC = 1.8 V to 5.5 V, T_A = −40°C to +85°C and V_CC = 2.5 V to 5.5 V, T_A = −40°C to +125°C, unless otherwise specified.
Symbol
Parameter
Test Conditions
Min
Max
I_CCR
I_CCW
I_SB
I_L
V_IL1
V_IL2
V_IH1
V_IH2
V_OL1
V_OL2
Read Current
Write Current
Standby Current
I/O Pin Leakage
Input Low Voltage
Input Low Voltage
Input High Voltage
Input High Voltage
Output Low Voltage
Output Low Voltage
Read, f_SCL = 400 kHz/1 MHz
All I/O Pins at GND or V_CC
Pin at GND or V_CC
2.5 V ≤ V_CC ≤ 5.5 V
1.8 V ≤ V_CC < 2.5 V
2.5 V ≤ V_CC ≤ 5.5 V
1.8 V ≤ V_CC < 2.5 V
V_CC ≥ 2.5 V, I_OL = 3.0 mA
V_CC < 2.5 V, I_OL = 1.0 mA
T_A = −40°C to +85°C
T_A = −40°C to +125°C
T_A = −40°C to +85°C
T_A = −40°C to +125°C
−0.5
−0.5
0.7 V_CC
0.75 V_CC
1
3
2
5
1
2
0.3 V_CC
0.25 V_CC
V_CC + 0.5
V_CC + 0.5
0.4
0.2
Units
mA
mA
mA
mA
V
V
V
V
V
V
Table 4. PIN IMPEDANCE CHARACTERISTICS
V_CC = 1.8 V to 5.5 V, T_A = −40°C to +85°C and V_CC = 2.5 V to 5.5 V, T_A = −40°C to +125°C, unless otherwise specified.
Symbol
Parameter
Conditions
Max
Units
C_IN (Note 4)
SDA I/O Pin Capacitance
V_IN = 0 V
8
pF
C_IN (Note 4)
Input Capacitance (other pins)
V_IN = 0 V
6
pF
I_WP, I_A (Note 5)
WP Input Current, Address Input
Current (A₀, A₁, A₂)
V_IN < V_IH, V_CC = 5.5 V
V_IN < V_IH, V_CC = 3.3 V
75
mA
50
V_IN < V_IH, V_CC = 1.8 V
25
V_IN > V_IH
2
4. These parameters are tested initially and after a design or process change that affects the parameter according to appropriate AEC−Q100
and JEDEC test methods.
5. When not driven, the WP, A₀, A₁, A₂ pins are pulled down to GND internally. For improved noise immunity, the internal pull−down is relatively
strong; therefore the external driver must be able to supply the pull−down current when attempting to drive the input HIGH. To conserve power,
as the input level exceeds the trip point of the CMOS input buffer (~ 0.5 x V_CC), the strong pull−down reverts to a weak current source.
http://onsemi.com
3