NS6A5.0AF-D Datasheet, PDF (2/4 Pages) ON Semiconductor – 600 Watt Peak Power Zener Transient Voltage Suppressors

NS6A5.0AFT3G Series
MAXIMUM RATINGS
Rating
Symbol
Value
Unit
Peak Power Dissipation (Note 1) @ T_L = 25°C, Pulse Width = 1 ms
DC Power Dissipation @ T_L = 75°C
Measured Zero Lead Length (Note 2)
Derate Above 75°C
Thermal Resistance from Junction−to−Lead
DC Power Dissipation (Note 3) @ T_A = 25°C
Derate Above 25°C
Thermal Resistance from Junction−to−Ambient
P_PK
P_D
R_qJL
P_D
R_qJA
600
W
1.5
W
20
mW/°C
50
°C/W
0.5
W
4.0
mW/°C
250
°C/W
Forward Surge Current (Note 4) @ T_A = 25°C
I_FSM
40
A
Operating and Storage Temperature Range
T_J, T_stg
−65 to +150
°C
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
1. 10 X 1000 ms, non−repetitive.
2. 1 in square copper pad, FR−4 board.
3. FR−4 board, using ON Semiconductor minimum recommended footprint, as shown in 403AA case outline dimensions spec.
4. 1/2 sine wave (or equivalent square wave), PW = 8.3 ms, duty cycle = 4 pulses per minute maximum.
ELECTRICAL CHARACTERISTICS (T_A = 25°C unless
otherwise noted, V_F = 3.5 V Max. @ I_F (Note 5) = 30 A)
Symbol
Parameter
I_PP
Maximum Reverse Peak Pulse Current
V_C
Clamping Voltage @ I_PP
V_RWM Working Peak Reverse Voltage
I_R
Maximum Reverse Leakage Current @ V_RWM
V_BR
Breakdown Voltage @ I_T
I_T
Test Current
I_F
Forward Current
V_F
Forward Voltage @ I_F
5. 1/2 sine wave (or equivalent square wave), PW = 8.3 ms,
non−repetitive duty cycle.
I
I_F
V_C V_BR V_RWM
II^{RT VF}
V
I_PP
Uni−Directional TVS
ELECTRICAL CHARACTERISTICS
Device
Device
Marking
V_RWM
(Note 6)
V
I_R @ V_RWM
mA
Breakdown Voltage
V_BR (Note 7) Volts
Min Nom Max
@ I_T
mA
V_C @ I_PP (Note 8)
V_C
I_PP
V
A
C_typ
(Note 9)
pF
NS6A5.0AFT3G
6AA
5.0
800
6.40
6.7
7.0
10
9.2
65.2
2700
NS6A12AFT3G
6AJ
12
0.5
13.3
14
14.7
1.0
19.5
31
1450
NS6A13AFT3G
6AK
13
5.0
14.4 15.15 15.9
1.0
21.5
27.9
1160
6. A transient suppressor is normally selected according to the working peak reverse voltage (V_RWM), which should be equal to or greater than
the DC or continuous peak operating voltage level.
7. V_BR measured at pulse test current I_T at an ambient temperature of 25°C.
8. Surge current waveform per Figure 1.
9. Bias Voltage = 0 V, F = 1 MHz, T_J = 25°C.
http://onsemi.com
2