MC74VHCU04_06 Datasheet, PDF (2/6 Pages) ON Semiconductor – Hex Inverter (Unbuffered)

MC74VHCU04
V_CC A6 Y6 A5 Y5 A4 Y4
14 13 12 11 10 9 8
1234567
A1 Y1 A2 Y2 A3 Y3 GND
(Top View)
Figure 2. Pinout: 14−Lead Packages
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _{MAXIMUM RATINGS}
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _Symbol
Parameter
Value
Unit
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _{VCC DC Supply Voltage}
–0.5 to + 7.0
V
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _{Vin DC Input Voltage}
–0.5 to + 7.0
V
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _{Vout DC Output Voltage}
–0.5 to V_CC + 0.5 V
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _{IIK Input Diode Current}
−20
mA
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _{IOK Output Diode Current}
± 20
mA
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _{Iout DC Output Current, per Pin}
± 25
mA
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _{ICC DC Supply Current, VCC and GND Pins}
± 50
mA
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _{PD Power Dissipation in Still Air,}
SOIC Packages†
500
mW
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ TSSOP Package†
450
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ T_stg Storage Temperature
– 65 to + 150
_C
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ^{Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress}
ratings only. Functional operation above the Recommended Operating Conditions is not implied.
Extended exposure to stresses above the Recommended Operating Conditions may affect device
reliability.
†Derating — SOIC Packages: – 7 mW/_C from 65_ to 125_C
TSSOP Package: − 6.1 mW/_C from 65_ to 125_C
RECOMMENDED OPERATING CONDITIONS
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _Symbol
Parameter
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _{VCC DC Supply Voltage}
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _{Vin DC Input Voltage}
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _{Vout DC Output Voltage}
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _{TA OperatingTemperature}
Min
Max Unit
2.0
5.5
V
0
5.5
V
0
V_CC
V
−40
+ 85
_C
This device contains protection
circuitry to guard against damage
due to high static voltages or electric
fields. However, precautions must
be taken to avoid applications of any
voltage higher than maximum rated
voltages to this high−impedance cir-
cuit. For proper operation, V_in and
V_out should be constrained to the
range GND v (V_in or V_out) v V_CC.
Unused inputs must always be
tied to an appropriate logic voltage
level (e.g., either GND or V_CC).
Unused outputs must be left open.
http://onsemi.com
2