MC74VHC4066_14 Datasheet, PDF (2/13 Pages) ON Semiconductor – Quad Analog Switch/ Multiplexer/Demultiplexer

MC74VHC4066
X_A ¹
2 _YA
A ON/OFF CONTROL ¹³
X_B ⁴
B ON/OFF CONTROL ⁵
X_C ⁸
3 _YB
ANALOG
OUTPUTS/INPUTS
9 _YC
C ON/OFF CONTROL ⁶
X_D ¹¹
D ON/OFF CONTROL ¹²
10 _YD
ANALOG INPUTS/OUTPUTS = X_A, X_B, X_C, X_D
PIN 14 = V_CC
PIN 7 = GND
Figure 1. Logic Diagram
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ^{MAXIMUM RATINGS}
Symbol
Parameter
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _{VCC Positive DC Supply Voltage (Referenced to GND)}
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _{VIS Analog Input Voltage (Referenced to GND)}
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _{Vin Digital Input Voltage (Referenced to GND)}
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _I
DC Current Into or Out of Any Pin
Value
Unit
– 0.5 to + 14.0
V
– 0.5 to V_CC + 0.5 V
– 0.5 to V_CC + 0.5 V
± 25
mA
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _{PD Power Dissipation in Still Air,}
SOIC Package†
500
mW
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _{TSSOP Packageâ€} 
450
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _{Tstg Storage Temperature}
– 65 to + 150
_C
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _{TL Lead Temperature, 1 mm from Case for 10 Seconds}
260
_C
†Derating — SOIC Package: – 7 mW/_C from 65_ to 125_C
TSSOP Package: − 6.1 mW/_C from 65_ to 125_C
RECOMMENDED OPERATING CONDITIONS
Symbol
Parameter
Min Max Unit
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _{VCC Positive DC Supply Voltage (Referenced to GND)}
2.0 12.0 V
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _VIS
Analog Input Voltage (Referenced to GND)
GND V_CC V
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _Vin
Digital Input Voltage (Referenced to GND)
GND V_CC V
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _{VIO* Static or Dynamic Voltage Across Switch}
— 1.2 V
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _TA
Operating Temperature, All Package Types
– 55 + 125 _C
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _{tr, tf}
Input Rise and Fall Time, ON/OFF Control
ns
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ^{Inputs (Figure 14)}
V_CC = 2.0 V 0 1000
V_CC = 3.0 V 0
600
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ _{VCC=4.5V 0}
500
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ^VCC^{=9.0V 0}
400
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ^{VCC=12.0V 0}
250
Functional operation above the stresses listed in the Recommended Operating Ranges is not
implied. Extended exposure to stresses beyond the Recommended Operating Ranges limits may
affect device reliability.
*For voltage drops across the switch greater than 1.2 V (switch on), excessive V_CC current may
be drawn; i.e., the current out of the switch may contain both V_CC and switch input
components. The reliability of the device will be unaffected unless the Maximum Ratings are
exceeded.
This device contains protection
circuitry to guard against damage
due to high static voltages or electric
fields. However, precautions must
be taken to avoid applications of any
voltage higher than maximum rated
voltages to this high−impedance cir-
cuit. For proper operation, V_in and
V_out should be constrained to the
range GND v (V_in or V_out) v V_CC.
Unused inputs must always be
tied to an appropriate logic voltage
level (e.g., either GND or V_CC).
Unused outputs must be left open.
I/O pins must be connected to a
properly terminated line or bus.
http://onsemi.com
2