MC74LVX8051_14 Datasheet, PDF (2/12 Pages) ON Semiconductor – Analog Multiplexer/ Demultiplexer

MC74LVX8051
X0 ¹³
X1 ¹⁴
X2 ¹⁵
ANALOG
INPUTS/
X3 ¹²
OUTPUTS _X4 ¹
X5 ⁵
X6 ²
X7 ⁴
A ¹¹
CHANNEL
SELECT
B ¹⁰
INPUTS _C ⁹
ENABLE ⁶
MULTIPLEXER/
DEMULTIPLEXER
PIN 16 = V_CC
PIN 8 = GND
3
X
COMMON
OUTPUT/
INPUT
LOGIC DIAGRAM
MC74LVX8051
Single−Pole, 8−Position Plus Common Off
FUNCTION TABLE − MC74LVX8051
Control Inputs
Enable
Select
CBA
ON Channels
L
LLL
L
L LH
L
LHL
L
L HH
L
HL L
L
HLH
L
HH L
L
HHH
H
XXX
X0
X1
X2
X3
X4
X5
X6
X7
NONE
X = Don’t Care
MAXIMUM RATINGS
Symbol
Parameter
Value
Unit
V_CC Positive DC Supply Voltage (Referenced to GND)
–0.5 to +7.0
V
V_IS Analog Input Voltage
−0.5 to V_CC + 0.5
V
V_in Digital Input Voltage (Referenced to GND)
–0.5 to V_CC + 0.5
V
I
DC Current, Into or Out of Any Pin
± 20
mA
P_D Power Dissipation in Still Air,
SOIC Package†
500
mW
TSSOP Package†
450
T_stg Storage Temperature Range
–65 to +150
_C
T_L Lead Temperature, 1 mm from Case for 10 Seconds
260
_C
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of
these limits are exceeded, device functionality should not be assumed, damage may occur and
reliability may be affected.
†Derating: SOIC Package: –7 mW/_C from 65_ to 125_C
TSSOP Package: −6.1 mW/_C from 65_ to 125_C
This device contains protection
circuitry to guard against damage
due to high static voltages or electric
fields. However, precautions must
be taken to avoid applications of any
voltage higher than maximum rated
voltages to this high−impedance cir-
cuit. For proper operation, V_in and
V_out should be constrained to the
range GND v (V_in or V_out) v V_CC.
Unused inputs must always be
tied to an appropriate logic voltage
level (e.g., either GND or V_CC).
Unused outputs must be left open.
RECOMMENDED OPERATING CONDITIONS
Symbol
Parameter
Min
Max
Unit
V_CC Positive DC Supply Voltage
(Referenced to GND)
2.5
6.0
V
V_IS Analog Input Voltage
0.0
V_CC
V
V_in Digital Input Voltage (Referenced to GND)
GND
V_CC
V
V_IO* Static or Dynamic Voltage Across Switch
1.2
V
T_A Operating Temperature Range, All Package Types
– 55
+ 85
_C
t_r, t_f Input Rise/Fall Time (Channel Select or Enable Inputs)
V_CC = 3.3 V ± 0.3 V
0
V_CC = 5.0 V ± 0.5 V
0
ns/V
100
20
Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond
the Recommended Operating Ranges limits may affect device reliability.
*For voltage drops across switch greater than 1.2 V (switch on), excessive V_CC current may be drawn; i.e., the current out of the switch may
contain both V_CC and switch input components. The reliability of the device will be unaffected unless the Maximum Ratings are exceeded.
http://onsemi.com
2