|
MC34160_06 Datasheet, PDF (2/10 Pages) ON Semiconductor – 100 mA, 5.0 V Voltage Regulator and Supervisory Circuit for Microprocessors | |||
|
◁ |
MC34160, MC33160
MAXIMUM RATINGS
Rating
Symbol
Value
Unit
Power Supply Voltage
Chip Disable Input Voltage (Pin 15, Note 1)
Comparator Input Current (Pins 1, 2, 9)
Comparator Output Voltage (Pins 6, 7, 8)
Comparator Output Sink Current (Pins 6, 7, 8)
Power Dissipation and Thermal Characteristics
P Suffix, DualâInâLine Case 648C
Thermal Resistance, JunctionâtoâAir
Thermal Resistance, JunctionâtoâCase (Pins 4, 5, 12, 13)
DW Suffix, Surface Mount Case 751G
Thermal Resistance, JunctionâtoâAir
Thermal Resistance, JunctionâtoâCase (Pins 4, 5, 12, 13)
Operating Junction Temperature
Operating Ambient Temperature
VCC
VCD
Iin
VO
ISink
MC34160
MC33160
RqJA
RqJC
RqJA
RqJC
TJ
TA
40
â0.3 to VCC
â2.0 to +2.0
40
10
80
15
94
18
+150
0 to +70
â40 to +85
V
V
mA
V
mA
°C/W
°C
°C
Storage Temperature Range
Tstg
â65 to +150
°C
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
1. The maximum voltage range is â0.3 V to VCC or +35 V, whichever is less.
ELECTRICAL CHARACTERISTICS (VCC = 30 V, IO = 10 mA, Iref = 100 mA) For typical values TA = 25°C, for min/max values TA is
the operating ambient temperature range that applies [Notes 2 and 3], unless otherwise noted.)
Characteristics
Symbol
Min
Typ
Max Unit
REGULATOR SECTION
Total Output Variation (VCC = 7.0 V to 40 V, IO = 1.0 mA to 100 mA, TA = Tlow to Thigh)
VO
4.75
5.0
5.25
V
Line Regulation (VCC = 7.0 V to 40 V, TA = 25°C)
Regline
â
5.0
40
mV
Load Regulation (IO = 1.0 V to 100 mA, TA = 25°C)
Regload
â
20
50
mV
Ripple Rejection (VCC = 25 V to 35 V, IO = 40 mA, f = 120 Hz, TA = 25°C)
RR
50
6.5
â
dB
REFERENCE SECTION
Total Output Variation (VCC = 7.0 to 40 V, IO = 0.1 mA to 2.0 mA, TA = Tlow to Thigh)
Vref
2.47
2.6
2.73
V
Line Regulation (VCC = 5.0 V to 40 V, TA = 25°C)
Regline
â
2.0
20
mV
Load Regulation (IO = 0.1 mA to 2.0 mA, TA = 25°C)
Regload
â
4.0
30
mV
RESET COMPARATOR
Threshold Voltage
High State Output (Pin 11 Increasing)
Low State Output (Pin 11 Decreasing)
Hysteresis
VIH
â
(VOâ0.11) (VOâ0.05) V
VIL
4.55 (VOâ0.18)
â
VH
0.02
0.07
â
Output Sink Saturation (VCC = 4.5 V, ISink = 2.0 mA)
VOL
â
â
0.4
V
Output OffâState Leakage (VOH = 40 V)
IOH
â
â
4.0
mA
POWER WARNING COMPARATOR
Input Offset Voltage
VIO
â
1.2
10
mV
Input Bias Current (VPin 9 = 3.0 V)
IIB
â
â
0.5
mA
Input Hysteresis Current (VPin 9 = Vref â 100 mV)
RPin 10 = 24 k
IH
RPin 10 = â
40
50
4.5
7.5
60
mA
11
Output Sink Saturation (ISink = 2.0 mA)
VOL
â
0.13
0.4
V
Output OffâState Leakage (VOH = 40 V)
IOH
â
â
4.0
mA
2. Tlo = 0°C for MC34160 Thigh = 70°C for MC34160
â40°C for MC33160
85°C for MC33160
3. Low duty cycle pulse testing techniques are used during test to maintain junction temperature as close to ambient as possible.
http://onsemi.com
2
|
▷ |