|
NCV7356_10 Datasheet, PDF (1/24 Pages) ON Semiconductor – Single Wire CAN Transceiver | |||
|
NCV7356
Single Wire CAN Transceiver
The NCV7356 is a physical layer device for a single wire data link
capable of operating with various Carrier Sense Multiple Access
with Collision Resolution (CSMA/CR) protocols such as the Bosch
Controller Area Network (CAN) version 2.0. This serial data link
network is intended for use in applications where high data rate is not
required and a lower data rate can achieve cost reductions in both the
physical media components and in the microprocessor and/or
dedicated logic devices which use the network.
The network shall be able to operate in either the normal data rate
mode or a highâspeed data download mode for assembly line and
service data transfer operations. The highâspeed mode is only
intended to be operational when the bus is attached to an offâboard
service node. This node shall provide temporary bus electrical loads
which facilitate higher speed operation. Such temporary loads should
be removed when not performing download operations.
The bit rate for normal communications is typically 33 kbit/s, for
highâspeed transmissions like described above a typical bit rate of
83 kbit/s is recommended. The NCV7356 features undervoltage
lockout, timeout for faulty blocked input signals, output blanking
time in case of bus ringing and a very low sleep mode current.
The device is compliant with GMW3089V2.4
General Motors Corporation specification.
Features
⢠Fully Compatible with J2411 Single Wire CAN Specification
⢠60 mA (max) Sleep Mode Current
⢠Operating Voltage Range 5.0 to 27 V
⢠Up to 100 kbps HighâSpeed Transmission Mode
⢠Up to 40 kbps Bus Speed
⢠Selective BUS WakeâUp
⢠Logic Inputs Compatible with 3.3 V and 5 V Supply Systems
⢠Control Pin for External Voltage Regulators (14 Pin Package Only)
⢠Standby to Sleep Mode Timeout
⢠Low RFI Due to Output Wave Shaping
⢠Fully Integrated Receiver Filter
⢠Bus Terminals ShortâCircuit and Transient Proof
⢠Loss of Ground Protection
⢠Protection Against Load Dump, Jump Start
⢠Thermal Overload and Short Circuit Protection
⢠ESD Protection of 4.0 kV on CANH Pin (2.0 kV on Any Other Pin)
⢠Undervoltage Lock Out
⢠Bus Dominant Timeout Feature
⢠Internally Fused Leads in SOâ14 Package
⢠NCV Prefix for Automotive and Other Applications Requiring Site
and Control Changes
⢠PbâFree Packages are Available
http://onsemi.com
8
1
SOICâ8
D SUFFIX
CASE 751
14
1
SOICâ14
D SUFFIX
CASE 751A
MARKING DIAGRAMS
8
1
14
V7356
ALYW
G
NCV7356G
AWLYWW
1
A
= Assembly Location
WL, L = Wafer Lot
Y
= Year
WW, W = Work Week
G or G = PbâFree Package
PIN CONNECTIONS
TxD 1
8 GND
MODE0 2
7 CANH
MODE1 3
6 LOAD
RxD 4
5 VBAT
(Top View)
GND 1
TxD 2
MODE0 3
MODE1 4
RxD 5
NC 6
GND 7
14 GND
13 NC
12 CANH
11 LOAD
10 VBAT
9 INH
8 GND
(Top View)
ORDERING INFORMATION
Device
Package
Shippingâ
NCV7356D1G
SOICâ8
(PbâFree)
98 Units / Rail
NCV7356D1R2G SOICâ8 2500 Tape & Reel
(PbâFree)
NCV7356D2
SOICâ14
55 Units / Rail
NCV7356D2G
SOICâ14
(PbâFree)
55 Units / Rail
NCV7356D2R2 SOICâ14 2500 Tape & Reel
NCV7356D2R2G SOICâ14 2500 Tape & Reel
(PbâFree)
â For information on tape and reel specifications,
including part orientation and tape sizes, please
refer to our Tape and Reel Packaging Specification
Brochure, BRD8011/D.
© Semiconductor Components Industries, LLC, 2010
1
January, 2010 â Rev. 8
Publication Order Number:
NCV7356/D
|
▷ |