NCP1015 Datasheet, PDF (1/22 Pages) ON Semiconductor – Self-Supplied Monolithic Switcher for Low Standby- Power Offline SMPS

NCP1015
Self-Supplied Monolithic
Switcher for Low Standby-
Power Offline SMPS
The NCP1015 integrates a fixed-frequency current-mode
controller and a 700 V voltage MOSFET. Housed in a PDIP-7 or
SOT-223 package, the NCP1015 offers everything needed to build a
rugged and low-cost power supply, including soft-start, frequency
jittering, short-circuit protection, skip-cycle, a maximum peak
current set-point and a Dynamic Self-Supply (no need for an auxiliary
winding).
Unlike other monolithic solutions, the NCP1015 is quiet by nature:
during nominal load operation, the part switches at one of the available
frequencies (65-100 kHz). When the current set-point falls below a
given value, e.g. the output power demand diminishes, the IC
automatically enters the so-called skip cycle mode and provides
excellent efficiency at light loads. Because this occurs at typically 0.25
of the maximum peak value, no acoustic noise takes place. As a result,
standby power is reduced to the minimum without acoustic noise
generation.
Short-circuit detection takes place when the feedback signal fades
away e.g. un-true short-circuit or is broken optocoupler cases. Finally
soft-start and frequency jittering further ease the designer task to
quickly develop low-cost and robust offline power supplies.
For improved standby performance, the connection of an auxiliary
winding stops the DSS operation and helps to consume less than
100ĂmW at high line.
Features
•ăBuilt-in 700ĂV MOSFET with typical R_DS(on) of 11 W
•ăLarge Creepage Distance between High-voltage Pins
•ăCurrent-mode Fixed Frequency Operation: 65 kHz - 100 kHz
•ăSkip-cycle Operation at Low Peak Currents Only: No Acoustic Noise!
•ăDynamic Self-Supply, No Need for an Auxiliary Winding
•ăInternal 1 ms Soft-start
•ăAuto-recovery Internal Output Short-circuit Protection
•ăFrequency Jittering for Better EMI Signature
•ăBelow 100ĂmW Standby Power if Auxiliary Winding is Used
•ăInternal Temperature Shutdown
•ăDirect Optocoupler Connection
•ăSPICE Models Available for TRANsient and AC Analysis
•ăThis is a Pb-Free Device
http://onsemi.com
MARKING
DIAGRAMS
8
1
PDIP-7
CASE 626A
AP SUFFIX
P1015APyy
AWL
YYWWG
1
4
4
SOT-223
CASE 318E
1
ST SUFFIX
AYW
1015yĂG
G
1
yy
y
A
WL
YY
WW
G or G
= 06 (65 kHz), 10 (100 kHz)
= A (65 kHz), B (100 kHz)
= Assembly Location
= Wafer Lot
= Year
= Work Week
= Pb-Free Package
(Note: Microdot may be in either location)
PIN CONNECTIONS
PDIP-7
V_CC 1
NC 2
8 GND
7 GND
GND 3
FB 4
5 DRAIN
(Top View)
SOT-223
V_CC 1
FB 2
4 GND
Typical Applications
•ăLow Power ac-dc Adapters for Chargers
•ăAuxiliary Power Supplies (USB, Appliances, TVs, etc.)
DRAIN 3
(Top View)
©Ă Semiconductor Components Industries, LLC, 2007
October, 2007 - Rev. 1
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 20 of this data sheet.
1
Publication Order Number:
NCP1015/D