MC14051B_06 Datasheet, PDF (1/12 Pages) ON Semiconductor – Analog Multiplexers/Demultiplexers

MC14051B, MC14052B,
MC14053B
Analog
Multiplexers/Demultiplexers
The MC14051B, MC14052B, and MC14053B analog multiplexers
are digitally−controlled analog switches. The MC14051B effectively
implements an SP8T solid state switch, the MC14052B a DP4T, and
the MC14053B a Triple SPDT. All three devices feature low ON
impedance and very low OFF leakage current. Control of analog
signals up to the complete supply voltage range can be achieved.
Features
• Triple Diode Protection on Control Inputs
• Switch Function is Break Before Make
• Supply Voltage Range = 3.0 Vdc to 18 Vdc
• Analog Voltage Range (V_DD − V_EE) = 3.0 to 18 V
Note: V_EE must be v V_SS
• Linearized Transfer Characteristics
• Low−noise − 12 nV/√Cycle, f ≥ 1.0 kHz Typical
• Pin−for−Pin Replacement for CD4051, CD4052, and CD4053
• For 4PDT Switch, See MC14551B
• For Lower R_ON, Use the HC4051, HC4052, or HC4053 High−Speed
CMOS Devices
• Pb−Free Packages are Available*
MAXIMUM RATINGS (Voltages Referenced to V_SS)
Symbol
Parameter
Value
Unit
V_DD DC Supply Voltage Range
(Referenced to V_EE, V_SS ≥ V_EE)
−0.5 to +18.0 V
V_in, Input or Output Voltage Range
−0.5 to V_DD + 0.5 V
V_out (DC or Transient) (Referenced to V_SS for
Control Inputs and V_EE for Switch I/O)
I_in Input Current (DC or Transient)
per Control Pin
+10
mA
I_SW Switch Through Current
± 25
mA
P_D Power Dissipation per Package (Note 1)
500
mW
T_A Ambient Temperature Range
−55 to +125
°C
T_stg Storage Temperature Range
−65 to +150
°C
T_L Lead Temperature (8−Second Soldering)
260
°C
Stresses exceeding Maximum Ratings may damage the device. Maximum
Ratings are stress ratings only. Functional operation above the Recommended
Operating Conditions is not implied. Extended exposure to stresses above the
Recommended Operating Conditions may affect device reliability.
1. Temperature Derating: Plastic “P and D/DW” Packages: – 7.0 mW/_C From
65_C To 125_C
This device contains protection circuitry to guard against damage due to high
static voltages or electric fields. However, precautions must be taken to avoid
applications of any voltage higher than maximum rated voltages to this
high−impedance circuit. For proper operation, V_in and V_out should be constrained to
the range V_SS v (V_in or V_out) v V_DD.
Unused inputs must always be tied to an appropriate logic voltage level (e.g., either
V_SS, V_EE or V_DD). Unused outputs must be left open.
*For additional information on our Pb−Free strategy and soldering details, please
download the ON Semiconductor Soldering and Mounting Techniques
Reference Manual, SOLDERRM/D.
http://onsemi.com
MARKING
DIAGRAMS
16
MC1405xBCP
1
PDIP−16
AWLYYWWG
P SUFFIX ₁
CASE 648
16
1405xBG
SOIC−16
AWLYWW
1
D SUFFIX
CASE 751B ¹
16
14
TSSOP−16
1
DT SUFFIX
05xB
ALYWG
G
CASE 948F ₁
16
MC1405xB
SOEIAJ−16
ALYWG
1
F SUFFIX
CASE 966 ¹
x
= 1, 2, or 3
A
= Assembly Location
WL, L = Wafer Lot
Y
= Year
WW, W = Work Week
G or G = Pb−Free Package
(Note: Microdot may be in either location)
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 9 of this data sheet.
© Semiconductor Components Industries, LLC, 2006
1
December, 2006 − Rev. 10
Publication Order Number:
MC14051B/D