MC10H334 Datasheet, PDF (1/4 Pages) ON Semiconductor – Quad Bus Driver/Receiver with Transmit and Receiver Latches

MOTOROLA
SEMICONDUCTOR TECHNICAL DATA
Quad Bus Driver/Receiver with
Transmit and Receiver Latches
MC10H334
The MC10H334 is a Quad Bus Driver/Receiver with transmit and receiver
latches. When disabled, (OE = high) the bus outputs will fall to –2.0 V. Data to
be transmitted or received is passed through its respective latch when the
respective latch enable (DLE and RLE) is at a low level. Information is latched
on the positive transition of DLE and RLE. The parameters specified are with
25 Ω loading on the bus drivers and 50 Ω loads on the receivers.
• Propagation Delay, 1.6 ns Typical Data–to–Output
• Improved Noise Margin 150 mV (Over Operating Voltage and
Temperature Range)
• Voltage Compensated
• MECL 10K–Compatible
L SUFFIX
CERAMIC PACKAGE
CASE 732–03
P SUFFIX
PLASTIC PACKAGE
CASE 738–03
FN SUFFIX
PLCC
CASE 775–02
MAXIMUM RATINGS
Characteristic
Symbol
Rating
Unit
Power Supply (VCC = 0)
Input Voltage (VCC = 0)
Output Current — Continuous
— Surge
VEE
VI
Iout
–8.0 to 0
Vdc
0 to VEE
Vdc
50
mA
100
Operating Temperature Range
Storage Temperature Range — Plastic
— Ceramic
TA
0 to +75
°C
Tstg
–55 to +150
°C
–55 to +165
°C
ELECTRICAL CHARACTERISTICS (VEE = –5.2 V ±5%) (See Note)
0°
25°
75°
Characteristic
Symbol Min Max Min Max Min Max Unit
Power Supply Current
IE
Input Current High
IinH
Pins 5,6,15,16
Pins 7,14
Pin 17
— 161 — 161 —
— 397 — 273 —
— 460 — 297 —
— 520 — 357 —
161 mA
µA
273
297
357
Input Current Low
High Output Voltage
Low Output Voltage
High Input Voltage
Low Input Voltage
AC PARAMETERS
IinL
VOH
VOL
VIH
VIL
0.5 — 0.5 — 0.3
—
µA
–1.02 –0.84 –0.98 –0.81 –0.92 –0.735 Vdc
–1.95 –1.63 –1.95 –1.63 –1.95 –1.60 Vdc
–1.17 –0.84 –1.13 –0.81 –1.07 –0.735 Vdc
–1.95 –1.48 –1.95 –1.48 –1.95 –1.45 Vdc
Propagation Delay
tpd
Data–to–Bus Output
DLE–to–Bus Output
OE–to–Bus Output
Bus–to–R0
RLE–to–R0
Data–to–Receiver
R0
ns
0.5 2.5 0.5 2.5 0.5 2.5
1.0 2.7 1.0 2.7 1.0 2.7
0.5 2.5 0.5 2.5 0.5 2.5
0.5 1.9 0.5 1.9 0.5 1.9
0.5 2.1 0.5 2.1 0.5 2.1
1.0 3.8 1.0 3.8 1.0 3.8
Rise Time
Fall Time
tr
0.5 2.2 0.5 2.2 0.5 2.2 ns
tf
0.5 2.2 0.5 2.2 0.5 2.2 ns
DIP & PLCC
PIN ASSIGNMENT
VCC
1
BUS1
2
BUS0
3
20
VCC03
19
BUS2
18
BUS3
VCC02
4
17
OE
D1
5
16
D2
D0
6
15
D3
DLE
7
14
RLE
R0
8
13
R3
R1
9
12
R2
VEE
10
11
VCC02
Pin assignment is for Dual–in–Line Package.
For PLCC pin assignment, see the Pin Conversion
Tables on page 6–11 of the Motorola MECL Data
Book (DL122/D).
NOTE:
Each MECL 10H series circuit has been designed
to meet the dc specifications shown in the test table,
after thermal equilibrium has been established. The
circuit is in a test socket or mounted on a printed
circuit board and transverse air flow greater than
500 Ifpm is maintained. Receiver outputs are
terminated through a 50–ohm resistor to –2.0 volts
dc. Bus outputs are terminated through a 25–ohm
resistor to –2.0 volts dc.
3/93
© Motorola, Inc. 1996
2–37
REV 5