MC10H330 Datasheet, PDF (1/4 Pages) ON Semiconductor – Quad Bus Driver/Receiver with 2-to-1 Output Multiplexers

MOTOROLA
SEMICONDUCTOR TECHNICAL DATA
Quad Bus Driver/Receiver with
2-to-1 Output Multiplexers
The MC10H330 is a Quad Bus Driver/Receiver with two–to–one output
multiplexers. These multiplexers have a common select and output enable.
When disabled, (OE = high) the bus outputs go to –2.0 V. Their output can be
brought to a low state (VOL) by applying a high level to the receiver enable (RE
= High). The parameters specified are with 25 Ω loading on the bus drivers and
50 Ω loads on the receivers.
• Propagation Delay, 1.5 ns Typical Data–to–Output
• Improved Noise Margin 150 mV (Over Operating Voltage and
Temperature Range)
• Voltage Compensated
• MECL 10K–Compatible
MAXIMUM RATINGS
Characteristic
Symbol
Rating
Unit
Power Supply (VCC = 0)
Input Voltage (VCC = 0)
Output Current — Continuous
— Surge
VEE
VI
Iout
–8.0 to 0
Vdc
0 to VEE
Vdc
50
mA
100
Operating Temperature Range
Storage Temperature Range — Plastic
— Ceramic
TA
0 to +75
°C
Tstg
–55 to +150
°C
–55 to +165
°C
ELECTRICAL CHARACTERISTICS (VEE = –5.2 V ±5%) (See Note)
0°
25°
75°
Characteristic
Symbol Min Max Min Max Min Max Unit
Power Supply Current
IE
Input Current High
IinH
Pins 5–8, 17–20
Pins 16, 21
Pin 9
— 157 — 143 —
— 667 — 417 —
— 514 — 321 —
— 475 — 297 —
157 mA
µA
417
321
297
Input Current Low
High Output Voltage
Low Output Voltage
High Input Voltage
Low Input Voltage
IinL
VOH
VOL
VIH
VIL
0.5 — 0.5 — 0.3
—
µA
–1.02 –0.84 –0.98 –0.81 –0.92 –0.735 Vdc
–1.95 –1.63 –1.95 –1.63 –1.95 –1.60 Vdc
–1.17 –0.84 –1.13 –0.81 –1.07 –0.735 Vdc
–1.95 –1.48 –1.95 –1.48 –1.95 –1.45 Vdc
AC PARAMETERS
Propagation Delay
tpd
Select–to–Input
Data–to–Bus Output
Select–to–Bus
Output
OE–to–Bus Output
Bus–to–Input
RE–to–Input
Data–to–Receiver
Input
ns
1.8 5.3 1.8 5.3 1.8 5.3
0.5 2.0 0.5 2.0 0.5 2.0
1.0 3.2 1.0 3.2 1.0 3.2
0.8 2.2 0.8 2.2 0.8 2.2
0.8 2.1 0.8 2.1 0.8 2.4
0.5 2.2 0.5 2.2 0.5 2.2
1.3 4.0 1.3 4.0 1.3 4.0
Rise Time
Fall Time
tr
0.5 2.0 0.5 2.0 0.5 2.0 ns
tf
0.5 2.0 0.5 2.0 0.5 2.0 ns
MC10H330
L SUFFIX
CERAMIC PACKAGE
CASE 758–02
P SUFFIX
PLASTIC PACKAGE
CASE 724–03
FN SUFFIX
PLCC
CASE 776–02
DIP
PIN ASSIGNMENT
VCC
1
24
VCC0
XBUS
2
23
YBUS
WBUS
3
22
ZBUS
VCC0
4
X1
5
21
OE
20
Y0
X0
6
19
Y1
W1
7
18
Z0
W0
8
17
Z1
S
9
16
RE
WIN
10
15
ZIN
XIN
11
VEE
12
14
YIN
13
VCC0
Pin assignment is for Dual–in–Line Package.
For PLCC pin assignment, see the Pin Conversion
Tables on page 6–11 of the Motorola MECL Data
Book (DL122/D).
NOTE:
Each MECL 10H series circuit has been designed
to meet the dc specifications shown in the test table,
after thermal equilibrium has been established. The
circuit is in a test socket or mounted on a printed
circuit board and transverse air flow greater than
500 Ifpm is maintained. Receiver outputs are
terminated through a 50–ohm resistor to –2.0 volts
dc. Bus outputs are terminated through a 25–ohm
resistor to –2.0 volts dc.
3/93
© Motorola, Inc. 1996
2–299
REV 5