MC10H186 Datasheet, PDF (1/4 Pages) ON Semiconductor – Hex D Master-Slave Flip-Flop with Reset

MOTOROLA
SEMICONDUCTOR TECHNICAL DATA
Hex D Master-Slave Flip-Flop
with Reset
The MC10H186 is a hex D type flip–flop with common reset and clock lines.
This MECL 10H part is a functional/pinout duplication of the standard MECL
10K family part, with 100% improvement in clock toggle frequency and
propagation delay and no increase in power–supply current.
• Propagation Delay, 1.7 ns Typical
• Power Dissipation, 460 mW Typical
• Improved Noise Margin 150 mV (Over Operating Voltage and
Temperature Range)
• Voltage Compensated
• MECL 10K–Compatible
MAXIMUM RATINGS
Characteristic
Symbol
Rating
Unit
Power Supply (VCC = 0)
Input Voltage (VCC = 0)
Output Current — Continuous
— Surge
VEE
–8.0 to 0
Vdc
VI
0 to VEE
Vdc
Iout
50
mA
100
Operating Temperature Range
Storage Temperature Range — Plastic
— Ceramic
TA
0 to +75
°C
Tstg
–55 to +150
°C
–55 to +165
°C
ELECTRICAL CHARACTERISTICS (VEE = –5.2 V ±5%) (See Note)
0°
25°
75°
Characteristic
Symbol Min Max Min Max Min Max Unit
Power Supply Current
Input Current High
Pins 5,6,7,10,11,12
Pin 9
Pin 1
IE
—
121
—
110
—
121 mA
IinH
µA
—
430
—
265
—
265
—
670
—
420
—
420
— 1250 —
765
—
765
Input Current Low
High Output Voltage
Low Output Voltage
High Input Voltage
Low Input Voltage
IinL
VOH
VOL
VIH
VIL
0.5
—
0.5
—
0.3
—
µA
–1.02 –0.84 –0.98 –0.81 –0.92 –0.735 Vdc
–1.95 –1.63 –1.95 –1.63 –1.95 –1.60 Vdc
–1.17 –0.84 –1.13 –0.81 –1.07 –0.735 Vdc
–1.95 –1.48 –1.95 –1.48 –1.95 –1.45 Vdc
AC PARAMETERS
Propagation Delay
tpd
0.7
3.0
0.7
3.0
0.7
3.0
ns
Set–up Time
tset
1.5
—
1.5
—
1.5
—
ns
Hold Time
thold
1.0
—
1.0
—
1.0
—
ns
Rise Time
tr
0.7
2.6
0.7
2.6
0.7
2.6
ns
Fall Time
tf
0.7
2.6
0.7
2.6
0.7
2.6
ns
Toggle Frequency
ftog
250
—
250
—
250
—
MHz
Reset Recovery Time
(t1–9+)
trr
3.0
—
3.0
—
3.0
—
ns
NOTE:
Each MECL 10H series circuit has been designed to meet the dc specifications shown in the test table,
after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed
circuit board and transverse air flow greater than 500 linear fpm is maintained. Outputs are terminated
through a 50–ohm resistor to –2.0 volts.
MC10H186
L SUFFIX
CERAMIC PACKAGE
CASE 620–10
P SUFFIX
PLASTIC PACKAGE
CASE 648–08
FN SUFFIX
PLCC
CASE 775–02
CLOCKED TRUTH TABLE
R
C
D
L
L
X
L
H*
L
L
H*
H
H
L
X
Qn+1
Qn
L
H
L
* A clock H is a clock transition from
a low to a high state.
DIP
PIN ASSIGNMENT
RESET
1
Q0
2
Q1
3
Q2
4
D0
5
D1
6
D2
7
VEE
8
16
VCC
15
Q5
14
Q4
13
Q3
12
D5
11
D4
10
D3
9
CLOCK
Pin assignment is for Dual–in–Line Package.
For PLCC pin assignment, see the Pin Conversion
Tables on page 6–11 of the Motorola MECL Data
Book (DL122/D).
3/93
© Motorola, Inc. 1996
2–280
REV 5