MC10H158 Datasheet, PDF (1/4 Pages) ON Semiconductor – Quad 2-Input Multiplexer(Non-Inverting)

MOTOROLA
SEMICONDUCTOR TECHNICAL DATA
Quad 2-Input Multiplexer
(Non-Inverting)
The MC10H158 is a quad two channel multiplexer with common input select.
A “high” level select enables input D00, D10, D20 and D30 and a “low” level
select enables input D01, D11, D21 and D31. This MECL 10H part is a
functional/pinout duplication of the standard MECL 10K family part, with 100%
improvement in propagation delay and no increase in power–supply current.
• Propagation Delay, 1.5 ns Typical
• Power Dissipation, 197 mW Typical
• Improved Noise Margin 150 mV (Over Operating Voltage and
Temperature Range)
• Voltage Compensated
• MECL 10K–Compatible
MAXIMUM RATINGS
Characteristic
Symbol
Rating
Unit
Power Supply (VCC = 0)
Input Voltage (VCC = 0)
Output Current — Continuous
— Surge
VEE
VI
Iout
–8.0 to 0
Vdc
0 to VEE
Vdc
50
mA
100
Operating Temperature Range
Storage Temperature Range — Plastic
— Ceramic
TA
0 to +75
°C
Tstg
–55 to +150
°C
–55 to +165
°C
ELECTRICAL CHARACTERISTICS (VEE = –5.2 V ±5%)
0°
25°
75°
Characteristic
Symbol Min Max Min Max Min Max Unit
Power Supply Current
IE
Input Current High
IinH
Pin 9
Pins 3–6 and 10–13
— 53 — 48 —
— 475 — 295 —
— 515 — 320 —
53 mA
µA
295
320
Input Current Low
High Output Voltage
Low Output Voltage
High Input Voltage
Low Input Voltage
AC PARAMETERS
IinL
VOH
VOL
VIH
VIL
0.5 — 0.5 — 0.3
—
µA
–1.02 –0.84 –0.98 –0.81 –0.92 –0.735 Vdc
–1.95 –1.63 –1.95 –1.63 –1.95 –1.60 Vdc
–1.17 –0.84 –1.13 –0.81 –1.07 –0.735 Vdc
–1.95 –1.48 –1.95 –1.48 –1.95 –1.45 Vdc
Propagation Delay
Data
Select
tpd
ns
0.5 1.9 0.5 1.9 0.5 2.0
1.0 2.9 1.0 2.9 1.0 2.9
Rise Time
tr
0.7 2.2 0.7 2.2 0.7 2.2 ns
Fall Time
tf
0.7 2.2 0.7 2.2 0.7 2.2 ns
NOTE:
Each MECL 10H series circuit has been designed to meet the dc specifications shown in the test table,
after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit
board and transverse air flow greater than 500 Iinear fpm is maintained. Outputs are terminated through
a 50–ohm resistor to –2.0 volts.
MC10H158
L SUFFIX
CERAMIC PACKAGE
CASE 620–10
P SUFFIX
PLASTIC PACKAGE
CASE 648–08
FN SUFFIX
PLCC
CASE 775–02
TRUTH TABLE
Select D0
L
X
L
X
H
L
H
H
D1 Q
L
L
H
H
X
L
X
H
DIP
PIN ASSIGNMENT
Q0
1
Q1
2
D11
3
D10
4
D01
5
D00
6
NC
7
VEE
8
16
VCC
15
Q2
14
Q3
13
D20
12
D21
11
D30
10
D31
9
SELECT
Pin assignment is for Dual–in–Line Package.
For PLCC pin assignment, see the Pin Conversion
Tables on page 6–11 of the Motorola MECL Data
Book (DL122/D).
3/93
© Motorola, Inc. 1996
2–238
REV 5