|
MC10H123 Datasheet, PDF (1/4 Pages) ON Semiconductor – Triple 4-3-3-Input Bus Driver | |||
|
MOTOROLA
SEMICONDUCTOR TECHNICAL DATA
Triple 4-3-3-Input Bus Driver
The MC10H123 is a triple 4â3â3âInput Bus Driver.
The MC10H123 consists of three NOR gates designed for bus driving
applications on card or between cards. Output low logic levels are specified with
VOL = â2.1 Vdc so that the bus may be terminated to â2.0 Vdc. The gate output,
when low, appears as a high impedance to the bus, because the output
emitterâfollowers of the MC10H123 are âturnedâoff.â This eliminates
discontinuities in the characteristic impedance of the bus.
The VOH level is specified when driving a 25âohm load terminated to â2.0
Vdc, the equivalent of a 50âohm bus terminated at both ends. Although 25
ohms is the lowest characteristic impedance that can be driven by the
MC10H123, higher impedance values may be used with this part. A typical
50âohm bus is shown in Figure 1.
⢠Propagation Delay, 1.5 ns Typical
⢠Improved Noise Margin 150 mV (Over Operating Voltage and
Temperature Range)
⢠Voltage Compensated
⢠MECL 10KâCompatible
MAXIMUM RATINGS
Characteristic
Symbol
Rating
Unit
Power Supply (VCC = 0)
Input Voltage (VCC = 0)
Output Current â Continuous
â Surge
VEE
VI
Iout
â8.0 to 0
Vdc
0 to VEE
Vdc
50
mA
100
Operating Temperature Range
Storage Temperature Range â Plastic
â Ceramic
TA
0 to +75
°C
Tstg
â55 to +150
°C
â55 to +165
°C
ELECTRICAL CHARACTERISTICS (VEE = â5.2 V ±5%) (See Note)
0°
25°
75°
Characteristic
Symbol Min Max Min Max Min Max Unit
Power Supply Current
Input Current High
Input Current Low
High Output Voltage
Low Output Voltage
High Input Voltage
Low Input Voltage
AC PARAMETERS
IE
IinH
IinL
VOH
VOL
VIH
VIL
â 60 â 56 â
60 mA
â 495 â 310 â 310 µA
0.5 â 0.5 â 0.3
â
µA
â1.02 â0.84 â0.98 â0.81 â0.92 â0.735 Vdc
â2.1 â2.03 â2.1 â2.03 â2.1 â2.03 Vdc
â1.17 â0.84 â1.13 â0.81 â1.07 â0.735 Vdc
â1.95 â1.48 â1.95 â1.48 â1.95 â1.45 Vdc
Propagation Delay
tpd
0.7 1.5 0.7 1.6 0.7 1.7 ns
Rise Time
tr
0.7 1.6 0.7 1.7 0.7 1.8 ns
Fall Time
tf
0.7 1.6 0.7 1.7 0.7 1.8 ns
NOTE:
Each MECL 10H series circuit has been designed to meet the dc specifications shown in the test table,
after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit
board and transverse air flow greater than 500 Ifpm is maintained. Outputs are terminated through a
50âohm resistor to â2.1 volts.
MC10H123
L SUFFIX
CERAMIC PACKAGE
CASE 620â10
P SUFFIX
PLASTIC PACKAGE
CASE 648â08
FN SUFFIX
PLCC
CASE 775â02
LOGIC DIAGRAM
4
5
3
6
7
9
10
2
11
VCC1 = PIN 1
VCC2 = PIN 16
12
VEE = PIN 8
13
15
14
DIP
PIN ASSIGNMENT
VCC1
1
BOUT
2
AOUT
3
AIN
4
AIN
5
AIN
6
AIN
7
VEE
8
16
VCC2
15
COUT
14
CIN
13
CIN
12
CIN
11
BIN
10
BIN
9
BIN
Pin assignment is for DualâinâLine Package.
For PLCC pin assignment, see the Pin Conversion
Tables on page 6â11 of the Motorola MECL Data
Book (DL122/D).
3/93
© Motorola, Inc. 1996
2â41
REV 5
|
▷ |