E2V-X2B1 Datasheet, PDF (5/6 Pages) Omron Electronics LLC – Proximity Sensors

Influence of Surrounding Metal
When embedding the Sensor in metal, be sure that the
clearances given in the following table are maintained.
Mutual Interference
When installing Sensors face-to-face or side-by-side, be sure
that the minimum distances given in table 2 are maintained.
m
t
d dia.
n
m
D
t
t
Table 1. Influence of Surrounding Metal
Item Model E2V-X2
E2V-X5
0
0
d dia.
12
18
D
0
0
m
12
24
n
18
27
(Unit: mm)
E2V-X10
0
30
0
45
45
Item Model
d dia.
D
m
n
E2V-X4
0
12
0
12
18
E2V-X8
0
18
0
24
27
E2V-X15
0 (See Note 1.)
30 (See Note 1.)
0 (See Note 1.)
45
45
Note 1: If the thickness of the mounting bracket (t) exceeds 5 mm,
be sure to install the Sensor so that ≥ 2, d (dia.) ≥ 45, and D ≥ 2.
A
Chart 2. Mutual Interference
Item Model E2V-X2
A
30
B
20
Item Model
A
B
E2V-X4
35
25
B
E2V-X5
50
30
E2V-X8
60
35
(Unit: mm)
E2V-X10
100
50
E2V-X15
120
70
Other Information
Sensing Distance
• The sensing distance depends on the sensing object size, material, and
thickness.
• If the sensing object has a thickness of less than 1 mm, the sensing
distance will decrease.
• In some cases, it may not be possible to detect stainless steel.
Use the following graph and the Influence of Sensing Object Size and
Material information in Engineering Data (Typical) as a reference.
Dimensions
Pre-wired Models
E2V-X2/X4
21 dia.
17
60
47
6-dia. vinyl-insulated round cable
with 3 conductors
(Conductor cross section: 0.5 mm²,
Insulator diameter: 1.9 mm),
Standard length: 2 m
E2V-X5/X8
29 dia.
24
M12×1
Indicator*1
4
Two clamping nuts
Toothed washer
60
52
42
6-dia. vinyl-insulated round cable
with 3 conductors
(Conductor cross section: 0.5 mm²,
Insulator diameter: 1.9 mm),
Standard length: 2 m
M18×1
E2V-X10/X15
42 dia.
36
Indicator*1
4
Two clamping nuts
Toothed washer
60
52
42
6-dia. vinyl-insulated round cable
with 3 conductors
(Conductor cross section: 0.5 mm²,
Insulator diameter: 1.9 mm),
Standard length: 2 m
Connector Models
E2V-X4@-M1
21 dia.
17
M12×1
E2V-X8@-M1
29 dia.
24
M18×1
E2V-X15@-M1
42 dia.
36
Aluminum and Iron Cuttings
Normally aluminum or iron cuttings will not be detected even if they adhere
to or accumulate on the sensing surface. Detection signals may be output
for the following. If this occurs, remove the cuttings from the sensing
surface.
Diameter of cutting = d and diameter of sensing surface = D
Cuttings in center of sensing surface
with d ≥ 2/3D
d
Pressed against
Cutting _{sensing surface.}
Model
(Unit: mm)
Size D
D ^Sensing
surface
Cutting
E2V-X2@/X4@
10
E2V-X5@/X8@
16
E2V-X10@/X15@
28
Tightening Torque
Do not tighten the nut with excessive force.
A washer must be used with the nut.
(Shielded Model)
Part B Part A
Model
Tightening
Part A
Torque _{Dimension(mm) Torque}
Part B
Torque
E2V-X2/X4
17
5.9N•m
9.8N•m
E2V-X5/X8
22
15N•m
45N•m
E2V-X10/X15
26
39N•m
78N•m
(Unit:mm)
65
52
47
Two
clamping nuts
M12×1
4
Toothed washer Four indicators.*
60
47
42
Two
clamping nuts
M12×1
4
Toothed washer Four indicators.*
63
49
44
42
M30×1.5
Indicator*1
Two clamping nuts
5
Toothed washer
*1 NO Models: Operation indicator (yellow) (flashing)
Setting indicator (yellow) (ON)
NC Models: Operation indicator (yellow) (ON)
M30×1.5
Two
clamping nuts
M12×1
Four indicators.*
5
Toothed washer
* Setting indicator (ON)
Operation indicator (flashing)
Pre-wired Connector Models
B
E
C
F
D
6-dia. vinyl-insulated round cable,
Standard length: 300 mm
Pre-wired Connector Models
Item Model E2V-X4@-M1TJ
A
M12×1
B
60
C
---
D
47
Indicator*1
Two clamping nuts
A
G
Toothed washer
*1 NO Models: Operation indicator (yellow) (flashing)
E
M12×1
Setting indicator (yellow) (ON)
F
NC Models: Operation indicator (yellow) (ON)
G
21 dia.
17
4
E2V-X8@-M1TJ
M18×1
60
52
42
29 dia.
24
4
E2V-X15@-M1TJ
M30×1.5
60
52
42
42 dia.
36
5
Mounting Hole Dimensions
Proximity Sensor dimensions
H ^{Dimension H (mm)}
M12
12.5
+0.5
0
dia.
M18
18.5
+0.5
0
dia.
M30
30.5
+0.5
0
dia.
This document provides information mainly for selecting suitable models. Please read the document Instruction Sheet carefully for information that the user must understand and accept
before purchase, including information on warranty, limitations of liability, and precautions.
OMRON Corporation
Industrial Automation Company
Sensing Devices Division H.Q.
Industrial Sensors Division
Shiokoji Horikawa, Shimogyo-ku,
Kyoto, 600-8530 Japan
Tel: [phone]
Fax: [phone]
Regional Headquarters
OMRON EUROPE B.V.
Sensor Business Unit
Carl-Benz-Str. 4, D-71154 Nufringen,
Germany
Tel: [phone]/Fax: [phone]
OMRON ELECTRONICS LLC
One Commerce Drive Schaumburg,
IL 60173-5302 U.S.A.
Tel: [phone]/Fax: [phone]
OMRON ASIA PACIFIC PTE. LTD.
No. 438A Alexandra Road # 05-05/08 (Lobby 2),
Alexandra Technopark, Singapore 119967
Tel: [phone]/Fax: [phone]
OMRON (CHINA) CO., LTD.
Room 2211, Bank of China Tower,
200 Yin Cheng Zhong Road,
Pu Dong New Area, Shanghai, 200120, China
Tel: [phone]/Fax: [phone]
Authorized Distributor:
Note: Specifications subject to change without notice.
Cat. No. D107-E1-01
0907